Memorex Mi3X Minimove Back Panel

Geschrieben von: Michael Johnson
  • Kommentare: 1
Memorex Mi3X Minimove Back Panel

Schwierigkeitsgrad

Moderate

Schritte

11

Zeitaufwand

20 - 30 Minuten

Einleitung

If you need to replace the back panel of the Minimove boombox, follow the steps from this guide. This guide will involve moderate disassembly of the device, including the removal of the back covering and base.

  1. KmQcd352mVxIQeuA

    • Remove the two plastic screw covers on the back of your Minimove by inserting the flat end of your plastic opening tool between the screw cover and the back panel and prying it out.

    • It may be helpful to pull the plastic covers out with your fingers once the top of the cover has been revealed by using the plastic opening tool.

  2. AefiKOflRYyH4eTk

    • This step will require at least a 30 mm Phillips #1 screwdriver.

    • Use a Phillips #1 screwdriver to remove the two 12 mm screws.

  3. KSj5nDHGMHNFVXuR

    • The bottom panel screws and screw covers must be removed in order to access the back panel.

    • Remove the four grey screw covers by inserting the plastic opening tool underneath the screw covers and rotating around the circumference.

    • The adhesive on the screw covers should be sticky enough to put the covers back on when re-assembling the device.

  4. 4pkB2QeWnc5MwUnx

    • Remove the two 8 mm screws with a Phillips #1 screwdriver.

    • Remove the two 12 mm screws with a long Phillips #1 screwdriver.

    One of my 12mm screws appears to be stripped, and neither of screwdrivers that are both long enough and narrow enough to reach it can turn it. Any ideas how to get it out? I have the other 5 screws out …

    Lotus Flower -

  5. IVFeO1lmvBweqDDB
    IVFeO1lmvBweqDDB
    mQGSMbaSCMD2aFlc

    • To remove the back panel, use the plastic opening tool and gently work around the outline of the panel. The outline wraps around the sides and can be spotted at the top back of the device.

  6. rQUuAUtT6BQT4Kji
    rQUuAUtT6BQT4Kji
    hMBIATPuKIlLWpvZ
    TKoGS1kiMMqQErHW

    • Be careful not to use too much force to remove the panel. The antenna wire is connected to the inside of the panel and may be damaged or ripped off if the panel is not gently removed.

    • After loosening the panel with the plastic opening tool, use moderate force to pry open the panel with your hands.

    • Carefully pull the panel off.

  7. e5MJgcPCLkGnxR2L

    • Use a Phillips #1 screwdriver to detach the wire from the back panel by removing the 8 mm screw connecting the wire to the antenna.

  8. ffPi5rJIPWHVRV3T
    ffPi5rJIPWHVRV3T
    MtdwfXag11Fj6UHt

    • If desired, the antenna can now be removed by pulling inwards and horizontal to the panel bottom.

  9. G1amdQisSBuEBnZN

    • Use the Phillips #1 screwdriver to remove the four 12 mm screws.

    • Remove the five 6 mm screws at the top with the same screwdriver.

  10. UsQuJTrdWgcT52ke

    • Use a Phillips #1 screwdriver and remove the two vertical 8 mm screws from the top.

  11. Cx1YDj43ToVpsAwQ
    Cx1YDj43ToVpsAwQ
    P3HM5Dn3Ixr2V64B

    • Pry open the inner back panel by inserting the plastic opening tool in the crack at the top corner.

    • Use moderate force to pry it open and take the cover off.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Michael Johnson

Mitglied seit: 31/01/14

237 Reputation

0 Kommentare