Motorola Moto Z Force Droid öffnen

Geschrieben von: Adam O'Camb
  • Kommentare: 50
Motorola Moto Z Force Droid öffnen

Schwierigkeitsgrad

Mittel

Schritte

14

Zeitaufwand

1 - 2 Stunden

Einleitung

Grundständige Anleitung

  1. AjRocAbWkFxAtIyY

    • Lege einen erwärmten iOpener fünf Minuten lang auf den unteren Bereich der rückseitigen Glasscheibe.

    • Die Scheibe ist sehr widerspenstig. Du musst vermutlich den iOpener mehrfach erwärmen und neu auflegen, bis die Scheibe warm genug ist. Beachte die Anleitung für den iOpener um Überhitzung zu vermeiden.

    • Ein Haartrockner, ein Heißluftgebläse oder eine Heizplatte können auch funktionieren. Sei aber vorsichtig und überhitze das Smartphone nicht. Das Display und der Akku sind sehr hitzeempfindlich.

    I was unable to get the iOpener to heat the glass panes hot enough to loosen the glue. I was able to use a heat gun. Just heat it on low setting for about 1.5 min. (Any longer and you risk damaging the phone.

    Kimball Marston -

    I heated the iOpener several times to no avail. Then when i switched from the pick to a box cutter (see my comment on next step) it turned out that the glue WAS heated enough.

    Michael Roland -

    I agree with the heat gun. Only needed to use it on low for a few seconds.  iOpener did not work, ended up using an exacto knife and heat gun after breaking the bottom glass. Found the replacement glass on Amazon for 6.99 for both pieces.

    zx12bullet -

    I did this with the iOpener, about 45 seconds on a 1200W+ microwave. The mistake I made was not realizing how thin the glass is. Think paper thin. You do not have to dig far to get into it. I did peel off a protective outer plastic that was on both of mine. Shattered the top one, learned, bottom one came out without issues.

    Paul Porter -

    The iOpener was completely useless. use he heat gun as suggested above.

    Patrick Connerney -

    Before you start, get some 91% Isopropyl Alcohol from the drug store, find an 1800 watt hair dryer and a box cutter blade, and order the replacement glass pieces from ebay or amazon. Once you have it all, put some alcohol on the edges, wait a couple of minutes, heat the glass for 30-60 sec with the hair dryer, and bulldoze the glass pieces with the blade and spudger. Unless you value your time at less than $7/hr, you’ll be happy you didn’t bother trying the 1% chance to save the original glass.

    Udo Dirkschneider -

  2. DOCDummBabKSVURP
    DOCDummBabKSVURP
    3YfWZiuPM2hAObof
    YWKLPbbePFhFrZAT

    • Setze ein Plektrum in den schmalen Spalt zwischen Rückgehäuse und Glasscheibe ein.

    • Der Spalt zwischen Scheibe und Rahmen ist sehr eng, es kann daher hilfreich sein, das Plektrum vor- und zurück zu ruckeln, während du es hineinschiebst. Du kannst auch mit einer dünnen Klinge oder einem metallenen Hebelwerkzeug die Scheibe etwas anheben, bevor du das Plektrum weiterschiebst. Arbeite langsam und beschädige nicht das Glas.

    • Wenn du Schwierigkeiten hast, das Plektrum einzusetzen, dann gehe einen Schritt zurück und erwärme die Scheibe erneut. Du brauchst schon recht viel Wärme, um die Scheibe zu lösen, vermeide es aber, den mittleren Bereich des Smartphones zu erhitzen, wo sich der Akku befindet.

    • Auch einige Tropfen Isopropylalkohol (mehr als 90%ig) an den Kanten der Scheibe können beim Ablösen helfen.

    • Heble nicht um die Ladebuchse herum. Sie ist von einem Kunstoffteil eingerahmt, das dabei beschädigt werden könnte.

    • Heble mit der Spitze des Plektrums unter der Glasscheibe vorsichtig nach oben, um die Scheibe und das Rückgehäuse ein wenig voneinander zu trennen.

    The opening picks are too thick and weak to accomplish this step. Plan on breaking the glass with a knife and replacing it with new glass from ebay. Search Dogxiong For Motorola Moto Z/Moto Z Force Black Back Rear Battery Housing Top if the following link doesn’t work: https://www.ebay.com/i/123308522723?chn=...

    Mike Thompson -

    This step was a challenge. The picks are quite thick. I ended up using a box cutter knife to carefully separate one corner. Then I used one of the picks to complete this procedure. Once I realized that this worked, I breathed a sigh of relief. Then I did the same thing for steps 5 & 6.

    Michael Roland -

    Agreed. There’s no way I could have done this without a heat gun, a ton of patience, and a really, really thin flat screw driver bit from my iFixit tool pack. I think it was the 1.3.

    bennettr8 -

    I used a single edge razor blade in a holder. This worked much better then trying to get a pick inserted. Also, you really have to get the panel warm to heat up the glue enough to break it loose.

    Donald Whitaker -

    I managed to remove the remove the panel without a heat gun, but I did carefully use a square end hobby knife blade to life the glass far enough to insert the pick. The adhesive is across the entire panel, so it does not feel like it is lifting correctly as only the local area will actually lift.

    David Small -

    IO found the Jimmy from my iFixit tool kit worked well with the iOpener and letting the opener sit for about 10 minutes then using a pick to keep the glass separated.

    Dave Johnson -

    Heat gun & Metal Putty knife will be your best friend. Use a lot of patience and not strength

    Dan B -

    iOpener then blow dryer. Used tweezers to lift the paper thin glass. Once I got movement I shoved the pick in to cut the rest of the glue.

    If you use a back cover like me, don't worry about scratching these glass panels. They're entirely pointless and not visible to be honest.

    Took maybe an hour to get through this part.

    Alvin Liu -

    Agreed. Hope you play guitar…because these picks are worthless for anything else. Use an exacto knife or razor blades of some sort.

    Chad Albertson -

    Boxcutter blade, hair dryer, and just bust the glass off. Not worth trying to save!

    Udo Dirkschneider -

  3. 6YBASVckOEUWu6Np
    6YBASVckOEUWu6Np
    TUenNAGhEE26mtVy
    5M4IDmKh3AduVPor

    • Schiebe das Plektrum zwischen Scheibe und Rückgehäuse.

    • Schiebe das Plektrum die ganze Länge der Scheibe entlang, um die Klebeverbindung zum Rückgehäuse aufzutrennen.

    The entire underside of the panel has adhesive to all the edges.

    David Small -

    I used the heat gun and it worked great.

    Kimberly Schroeder -

  4. V3aEuB2xT2LHrKaq
    V3aEuB2xT2LHrKaq
    WEBNayKnyhPJe4ZV
    insKBrmSVuCn1sdw

    • Heble vorsichtig die Scheibe mit dem Plektrum hoch.

    • Entferne die Glasscheibe.

  5. ePeHsUrfwSADBUUk

    • Wiederhole die vorherigen vier Schritte (Erhitzen und Ablösen) für die obere Glasscheibe.

    • Beim Zusammenbau musst du alle Klebstoffreste von den Scheiben und dem Rückgehäuse entfernen. Reinige dann die Klebeflächen mit hochkonzentriertem Isopropylalkohol (mehr als 90%ig) und einem fusselfreien Tuch. So kann der Kleber wieder gut haften.

    • Befestige die Scheiben mit vorgestanzten Klebestreifen oder doppelseitigem Klebeband.

    When cleaning the Glass Panes, DO NOT use metal tools, This will scrape the paint off of the back of the glass and damage the glass. Use of Alcohol helps loosen and remove the glue. I used a small plastic scraper and alcohol. Just takes a little bit of time.

    Kimball Marston -

    I was unable to remove the top one with the tools provided. I ended up breaking the glass and had to take it piece by piece. It depends the age of the phone and how strong the adhesive was. You can buy replacements on eBay or Amazon ( https://www.amazon.com/Dogxiong-Battery-... ). I bought it while I was fixing the phone since I broke the glass.

    Charlie Gates -

    The upper glass panel proved to be more tricky. The previous square end hobby knife blade kept breaking, so I had to get a new regular hobby knife blade, which still broke, but managed to pry the panel up enough to get the other blade and eventually the pick in it. Wear safety glasses when prying with a metal blade  The entire panel has adhesive, but the right side when viewed in the above photo has less, so it should be easier to lift. Additional examination of the adhesive reveals that there is a small spot in the corner that does not have any adhesive, presumably to aid with disassembly.

    David Small -

    Got it off but it is all broken up, The top is definitely better adhered than the bottom.

    Dave Johnson -

    SO MUCH ADHESIVE!! Just break it off and get replacement glass for $7.

    Udo Dirkschneider -

    I was unable to get the adhesive off without breaking it using the iopener, but a heat gun did the trick real fast. would definitely recommend over the iopener

    Daniel Malkowski -

  6. sNKaYVF4KKXC4Gig

    • Entferne die sechs 4 mm Torx T3 Schrauben, mit denen die Displayeinheit befestigt ist.

    Why did they give me a T5 when it clearly states a T3?

    Good thing I had their other tool kit with all of the bits.

    Dave Johnson -

    what do you do if one of the Torx screw heads falls apart so you can’t turn the screw?

    Dave Johnson -

    I ground the head off with a very small Dremel grinding tip. I wil find out if I created any new problems when I connect the new battery. Not even sure the battery is the problem. My daughters phone just stopped working and wouldn’t turn on even when plugged in.

    I guess if the battery isn’t the problem, then I cna’t make it any worse.

    Dave Johnson -

    I ordered the sjtek kit:

    “Motorola Moto Z Force Droid XLTE XT1650-02 Screen Replacement LCD Display Touch Screen Digitizer Glass Assembly Parts 5.5" AMOLED Black with Frame”

    It came with the wrong sized screwdriver as the previous poster described. By the time I could tell something was wrong with the screwdriver, I had two stripped screw heads. Don’t order this kit unless you have your own set of phone repair tools

    Evan Bossonis -

    @ewb62 The iFixit kit includes both the T3 and T5 driver bits—however, the T3 is commonly packed in the parts tray, rather than the tools tray with the other driver bits. Check the entire package carefully and you should find it. If not, contact customer support so they can ship the missing bit out to you ASAP. Sorry for the confusion!

    Jeff Suovanen -

    I have the T5!!! Where's the T3??? Unbelievable.

    Kimberly Schroeder -

    Never mind. I ordered the wrong kit. The Z force has the 4 bits

    Kimberly Schroeder -

  7. XehagEetdFHKtddW
    XehagEetdFHKtddW
    MPVtevSrmbY5nKWb
    sDFU1II3WTDrpYQf

    • Setze die Spudgerspitze in das Loch in der rechten unteren Ecke des Rückgehäuses ein.

    • Drücke den Spudger in das Loch hinein, um so das Display vom Rückgehäuse zu lösen.

    Expect to bend the end of the spudger as the adhesive holding the display on is rather strong.

    David Small -

  8. QluWrMd42RvsnXgZ
    QluWrMd42RvsnXgZ
    FZLSbRKNLZHZqBvy

    • Halte mit dem Finger den Spalt zwischen Displayeinheit und Rückgehäuse offen und entferne den Spudger.

    • Setze dann das flache Ende des Spudgers in den Spalt zwischen dem Rückgehäuse und der Displayeinheit ein.

    Due to the display being hard to move, I push it far enough with the spudger until I was able to insert a pick to hold it while I shifted the spudger.

    David Small -

    I broke the display and had to buy another one because I didn't realize this part is 3- layered. I accidentally separated the glass from the digitizer. : ( so make sure you pop out the entire thicknesses with the spudger before you try lifting it away from the phone.

    Ingrid Leidy-Hayden -

  9. FEnUdY3BZTPrR2Qc
    FEnUdY3BZTPrR2Qc
    VCKjDWrwnh3Oca4G
    e1oXDLUcwdDLwRwf

    If it is being difficult, confirm that you have removed all 6 (SIX) screws. This is from personal experience.

    Charlie Gates -

    BECAREFUL twisting the spudger. You need to be right on the clip. If you are too far away from the clip you will crack the LCD screen from the inside (happened to me and ended up having to buy a new screen). I found a video where it shows working one of the picks all the way around the screen first to separate the glue / sealant that is used FIRST. then you can locate the clips easier Prying after all the glue is worked loose make it sperate a lot easier.

    HINT - The clip on the button side is not in the middle of the side it is slightly higher towards the Power button. The left side (no buttons) the clip is directly in the middle of the side.

    zx12bullet -

    I recommend moving the supdges slowly to let the adhesive separate on its own.

    David Small -

  10. yUWsdoPbUuKngNQ3
    yUWsdoPbUuKngNQ3
    4m45aESIQdmYPHwm
    UEVsCAjTZSI1jIxI

    • Wiederhole dieses Verfahren des Trennens und Hebelns an der anderen Seite des Smartphones.

    • Auf jeder Seite des Smartphones gibt es eine Raste. Achte darauf, dass beide gelöst sind, bevor du weitermachst.

    • Achte darauf, die Unterkante des Displays nicht mehr als 13 mm vom Rückgehäuse zu entfernen. Das Displaykabel ist immer noch verbunden und kann beschädigt werden, wenn die Unterseite zu weit geöffnet wird.

    On this side, I got the spudger 1/2 way up, and it wouldn’t give. I wound up working around from the other side, then down from the top to finally release it. It felt like the tension was released after everything else came out, and it popped right out. jml.

    James Lang -

    Clips are a broad term. No pictures of what to release and how. Ruined digitizer following these instructions.

    Rick Miller -

  11. SXE4EStpTkJr3EXx
    SXE4EStpTkJr3EXx
    q3IhXEpctQqBAGlO

    • Kippe die obere rechte Ecke des Displays nach unten, um eine der Laschen auszuklinken, die das Display oben festhalten.

    • Kippe als nächstes die andere Ecke nach unten, um die andere Lasche auszuklinken.

    • Das Displaykabel ist immer noch angeschlossen und kann beschädigt werden, wenn das Display zu viel bewegt wird. Sei vorsichtig beim Kippen und halte an, wenn du größeren Widerstand bemerkst.

    I still don’t know how this was supposed to work, but there is some adhesive along the top. I used the pick to wiggle the top out and then proceed. Another site advised more heat in this area to loosen the adhesive. I didn’t need to.

    bennettr8 -

    I also agree with this. I just kept shaking things until it loosened. Getting it back on was just as a struggle and took some forcing.

    Charlie Gates -

    The tabs are two small bumps that are located roughly at either end of the speaker. Careful prying with the pick may help, but make sure you do not over extend the bottom of the display.

    David Small -

    On reassembly, not that the camera under the display may be loose. Putting some pressure on the speaker while pressing up on the display should cause the top tabs to snap back in.

    David Small -

    I snapped the tab located on the right of the screen. This step might be the trickiest because it’s not clear how to wiggle and budge this screen to open like a book. Fortunately the screen was still functional

    Dan B -

    I found the previous step wasn’t clear enough about prying the screen past the midway point once you get to those 2 side tabs. I used the pick to keep separating the screen past those side tabs up until I reached the top corners. Then I laid the phone down, screen side up. I held onto the metal frame with one hand, and with my other hand I grasped the screen near the bottom side (by the fingerprint reader) and gently wriggled the screen left and right, with slight pressure in the direction of the fingerprint reader, and a little torque in the direction of opening in the “book” layout shown above. Voila! Opened like a charm.

    Kirk Lau -

  12. x5MMUNPNlJMuQWfi
    x5MMUNPNlJMuQWfi
    QgAYxLaXEGfe4ZC6
    HF6Jl2wF2rOWk6ti

    • Hebe die rechte Kante des Displays an und schlage es auf wie eine Buchseite, aber nicht mehr als 45°.

    • Hebe das Display vorsichtig etwas an, um die Raste an der Kante des Rückgehäuses zu lösen, wobei du den 45° Winkel beibehalten musst.

    • Lege das Display auf die Tischplatte hinter dem Smartphone ab und öffne es bis auf 90°, so dass du an das Displaykabel herankommen kannst.

    Note that there are several strips of glue along the edges of the display which will need to be reapplied during reassembly.

    Kimball Marston -

    During reassembly (once you have put the display cable back into its socket), I recommend plugging the charger cable into the phone for a few seconds to see if you see the lightening bolt (charging indicator) on the front panel. This will allow you to be certain that, both, the battery and display connectors have been properly and securely connected.

    Michael Roland -

  13. 2Lb5nuwWrU2jci3B
    2Lb5nuwWrU2jci3B
    mkw5ohUVKDAGxUdA

    • Hebe den Displaykabelstecker mit dem flachen Ende des Spudgers aus seinem Anschluss heraus.

    • Heble nur am Displaystecker und nicht am Anschluss auf der Hauptplatine.

    • Wenn du beim Zusammenbau hier angelangt bist und das Display angeschlossen ist, dann schaltet das Smartphone ein und überprüfe alle Display-Funktionen. Wenn alles in Ordnung ist, dann schaltet das Smartphone wieder aus und fahre mit dem Zusammenbau fort.

    • Wenn es nicht funktioniert, dann überprüfe nochmals, ob alles korrekt zusammengebaut ist, und ob die Stecker sauber sind. Unser Forum hilft dir bei der Fehlersuche.

    Note that the ribbon cable has adhesive beside the connector.

    David Small -

    When it is plugged into power on reassembly, it should show a lightening bolt. If it shows the restart screen, likely the battery was not connected correctly.

    David Small -

  14. 6QhdhPNu4YJXPn2u

    • Entferne das Display.

    • Wenn du beim Zusammenbau die Klebestreifen am Display ersetzen willst, dann schabe zuerst mit einem Spudger alle Klebstoffreste ab und reinige die Klebeflächen mit etwas hochkonzentriertem Isopropylalkohol (mindestens 90%ig) und einem fusselfreien Tuch.

    • Bringe an den Bereichen wo der alte Kleber war einen dünnen gut haftenden Klebestreifen an, wie etwa den 1 mm Tesa 61395, oder einen vorgestanzten Klebestreifen.

    • Wenn du eine neue Displayeinheit einbaust, dann schaue dir genau an, wo die Klebestellen am alten Display waren und befestige die Klebestreifen in gleicher Weise am neuen Ersatzteil.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

Tinte & Feder

Adam O'Camb

Mitglied seit: 11/04/15

178852 Reputation

0 Kommentare