Einleitung

The motherboard acts as the "brain" of the phone. Any damage the phone sustains to this region generally causes major malfunctions; thus, you should take extra care while removing/replacing this piece.

  1. 2svKcraqZVtTgbW6
    2svKcraqZVtTgbW6
    OduWAbXLVyaHuENv
    xOLn5aKaP5DfCj5I
    • First, on the back of the phone find the silver button on the top left corner of the phone.

    • Simultaneously push down the button and slide the back plate down to reveal the battery.

  2. P364auIDATUUMEJf
    P364auIDATUUMEJf
    bgowepgMkhccTRY2
    • Grab the lower edge of the battery at the two bottom corners.

    • Pull upward on the edges to remove the battery.

  3. Xbh4sHTDiVOGnIa2
    Xbh4sHTDiVOGnIa2
    lwNtPlq3hasOryJv
    trynomSINJesIKQO
    • Push the metal slider towards the top of the phone until it clicks out of the original position.

    • Gently slide out and remove the SIM card.

  4. Lp5wvtl43A3oQjDX
    Lp5wvtl43A3oQjDX
    qZubpDKMyYN3VAMw
    • Grip the antenna and twist it counterclockwise to loosen it.

    • When it has been loosened all the way, pull gently to remove the antenna piece.

    Step 4 — To remove the Antenna ¶

    1) Loosen it.

    a) Grip the antenna

    b)Twist it counterclockwise tilll it loosens completely.

    2)Pull the antenna gently.

    Divya -

  5. KpKkSdlhOqHtD3Jr
    KpKkSdlhOqHtD3Jr
    RrOd5TXcfwhrISc6
    NtjwlXJkdPbYVisU
    • Using a pin, gently pry the top two screw covers off.

    • The large cover in the upper left of the back plate does not need to be removed.

  6. P5PXeDGIKj1GlieL
    P5PXeDGIKj1GlieL
    3jUXVcoHk5NmsPHn
    ZepVmdqXkGoDiwQS
    • At the corners of the phone, remove all four 6.0 mm Torx screws.

  7. iBjB5aYTtplSALCZ
    iBjB5aYTtplSALCZ
    i3ELT2BGqVBfIRNv
    LKSRmTSPAoXe2MVs
    • Next, insert a spudger into the marked holes, one at a time, and pry away from the phone to release the internal tabs.

    • Then, separate and detach the rear casing.

  8. 5JqNSqZYvcwEARcH
    5JqNSqZYvcwEARcH
    OsxVhvRvSQgd1CVw
    41BsOlDRyAPFqHUN
    • Separate the front ribbon cable from the board with a plastic opening tool.

  9. uQXYqkNK5IsHyilI
    uQXYqkNK5IsHyilI
    LKQOIQUMILcZNDJf
    T5RiswFe2kaHsmFC
    • Make sure you don’t break the ribbon cables that attach to the side buttons when removing the motherboard.

    • Lift out the motherboard only after all cables have been disconnected. Try to touch it only from the sides.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Chad Brantley

Mitglied seit: 06/10/10

32 Reputation

0 Kommentare