NETGEAR WGT624 v3 Antenna Replacement

Geschrieben von: Jonathon Sather
  • Kommentare: 0
NETGEAR WGT624 v3 Antenna Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

15 Minuten

Einleitung

Removing the antenna will allow you access to other parts of the device or it can replace the antenna if it is not working properly.

  1. V6qAE3xo3ETcsUPt

    • Turn the device so that the bottom is facing up.

  2. HfLKlfn1POushN5C
    HfLKlfn1POushN5C
    T1rdEJuU51M4xIcp
    xRxFBxwNoyTOTkyE

    • Use the plastic opening tool to carefully lift the rubber stops in each corner.

    • Do not completely remove the rubber stops, because they are difficult to replace.

  3. X5cBjW2YyNFv1tGI
    X5cBjW2YyNFv1tGI
    5u4cfJdemplNBtJx

    • Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.

  4. WQMOmqQGAwLrFm4X
    WQMOmqQGAwLrFm4X
    VIHvuhBSJh4wwXSl

    • Lift the lower case straight up from the rest of the router.

  5. XsWUcfGOXxeAuJWV
    XsWUcfGOXxeAuJWV
    MjXFBtnDHAOIjeGJ

    • Remove the clear plastic casing by lifting it straight up from the router.

  6. hEpVMWvM2COMejTi
    hEpVMWvM2COMejTi
    pLXdfUslHSgU1Pn4

    • Separate the motherboard from the top shell by lifting it straight up from the router.

  7. QHBXDKiEUM5j4qsS

    • Turn the motherboard, so that the top is facing upwards.

    • Place the motherboard on a clean flat surface.

  8. 5UVrWmAfxJWAElGU
    5UVrWmAfxJWAElGU
    Tog15Y3kZHDYKfCb

    • Remove the yellow tape that holds the wire.

    • Make sure that you set the tape aside on a clean surface, so that it can be reused.

  9. WlWmIFKsLdEUujB4
    WlWmIFKsLdEUujB4
    etEqTs2hbswGX1Jh
    IUmxPronPDMxRESc

    • Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard.

    • The wire should now be completely separate from the motherboard.

  10. mAx4ismBeNOnycnQ

    • Extend the antenna away from the device, so that it becomes straight.

  11. OyF6AwvBywYgXi25
    OyF6AwvBywYgXi25
    HLRRBSBPnu3c36hA
    RwPouepPMIRJpCwP

    • Find the clips that hold the antenna onto the router.

    • Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole.

    • The antenna may take considerable force to remove.

  12. aaRVeWSU1y3qACZJ

    • Completely separate the antenna and wire from the rest of the device.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jonathon Sather

Mitglied seit: 23/01/13

45 Reputation

0 Kommentare