Einleitung

Use this guide to remove the inner plastic components.

  1. UwU3B6SuBenHBOnU
    UwU3B6SuBenHBOnU
    PbVuNSSem5NklwO4
    qYYVnhaTROKD4Vhh
    • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

    • Remove the two 9.0 mm Phillips screws securing the battery compartment.

    • Slide the battery compartment out.

  2. bvTNo3JklxtXLIuV
    • Remove the five 9.0 mm Phillips screws securing the trigger.

  3. VxMB5HHviFfcuGjj
    VxMB5HHviFfcuGjj
    CiiM6ZBwNws1ZpXY
    • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

    • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

  4. 1MqDDotCJjTFNQhN
    1MqDDotCJjTFNQhN
    RDLqsBGyApVmRsnf
    YiqeuNWEeoYxljKq
    • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

    • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

  5. dRL1yeTVSbU6F2lV
    • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

  6. P1fl6YiMt5tiTauh
    • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

  7. aqB51xsxTwTMZafB
    • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

    • Remove the single 7.0 mm Phillips screw below the barrel.

    • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

  8. iqEHJUmORL2wlKvX
    • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

  9. RWZNDbeAAknyqKMR
    RWZNDbeAAknyqKMR
    i6vMALlwy1o6m2wk
    • Remove the two 9.0 mm Phillips screws holding together the handle.

    • Remove the plastic cover of the handle.

  10. TCURSiSCVNZVbGdq
    TCURSiSCVNZVbGdq
    4gIEGAZP6SkDm5lI
    • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

    • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

  11. cgjkZK4I5luyetIo
    cgjkZK4I5luyetIo
    cXLTpFe2QhmeTrTC
    lJGAYDfsZ6GOwVDY
    • Pull one end of the handle away from the orange latch.

    • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

  12. NMVmHRVC6vhRoD6Z
    NMVmHRVC6vhRoD6Z
    EycP1apPGwnDdX1Q
    DylRsWf4DjGmDNMG
    • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

    • Completely remove the left shell from the rest of the Nerf Gun.

  13. 5EMgb4VFId6gJOgG
    5EMgb4VFId6gJOgG
    yhQ4O6ZlQZWCa2g1
    CcFclaMSyFJvyOmX
    • Remove the cartridge support.

  14. LqCOwHwFV4UMGy1b
    LqCOwHwFV4UMGy1b
    WL3OXO6pWHGo2cEP
    rxtpTIyBGif3QlCM
    • Remove the handle crank.

  15. IEDSj5P6NPgOCXLL
    IEDSj5P6NPgOCXLL
    ZBdZG3DuuRXvIKd3
    • Remove the clear plastic barrel cover.

  16. CtcunV65cLuG4iyJ
    CtcunV65cLuG4iyJ
    GkRmSRmAwKgEFNam
    • Remove the firing pin.

    Not a pin, rather a plastic arm called the pusher

    Tribit Fan Opex ツ -

Abschluss

To reassemble your device, follow these instructions in reverse order.

sage

Mitglied seit: 24/01/14

301 Reputation

0 Kommentare