Nerf N-Strike Elite Hail-Fire Left Shell Replacement

Geschrieben von: Aaron Poon
  • Kommentare: 0
Nerf N-Strike Elite Hail-Fire Left Shell Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

15 - 30 Minuten

Einleitung

Use this guide to detach the damaged left shell so you'll be able to replace it with an undamaged shell. This guide can also be used with the 5 other Nerf N-Strike Elite Hail-Fire guides to replace other parts.

  1. UwU3B6SuBenHBOnU
    UwU3B6SuBenHBOnU
    PbVuNSSem5NklwO4
    qYYVnhaTROKD4Vhh

    • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

    • Remove the two 9.0 mm Phillips screws securing the battery compartment.

    • Slide the battery compartment out.

  2. bvTNo3JklxtXLIuV

    • Remove the five 9.0 mm Phillips screws securing the trigger.

  3. VxMB5HHviFfcuGjj
    VxMB5HHviFfcuGjj
    CiiM6ZBwNws1ZpXY

    • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

    • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

  4. 1MqDDotCJjTFNQhN
    1MqDDotCJjTFNQhN
    RDLqsBGyApVmRsnf
    YiqeuNWEeoYxljKq

    • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

    • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

  5. dRL1yeTVSbU6F2lV

    • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

  6. P1fl6YiMt5tiTauh

    • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

  7. aqB51xsxTwTMZafB

    • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

    • Remove the single 7.0 mm Phillips screw below the barrel.

    • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

  8. iqEHJUmORL2wlKvX

    • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

  9. RWZNDbeAAknyqKMR
    RWZNDbeAAknyqKMR
    i6vMALlwy1o6m2wk

    • Remove the two 9.0 mm Phillips screws holding together the handle.

    • Remove the plastic cover of the handle.

  10. TCURSiSCVNZVbGdq
    TCURSiSCVNZVbGdq
    4gIEGAZP6SkDm5lI

    • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

    • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

  11. cgjkZK4I5luyetIo
    cgjkZK4I5luyetIo
    cXLTpFe2QhmeTrTC
    lJGAYDfsZ6GOwVDY

    • Pull one end of the handle away from the orange latch.

    • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

  12. NMVmHRVC6vhRoD6Z
    NMVmHRVC6vhRoD6Z
    EycP1apPGwnDdX1Q
    DylRsWf4DjGmDNMG

    • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

    • Completely remove the left shell from the rest of the Nerf Gun.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Aaron Poon

Mitglied seit: 24/01/14

217 Reputation

0 Kommentare