Einleitung

In order to replace this part of the camera, you will need to use the spudger tool and the Phillips screwdriver. Maker sure to keep track of all the screws as you take the device apart.

  1. MCho5h1hCdstl6Yn
    MCho5h1hCdstl6Yn
    IBTaglLRgGLlCHVV
    2vmefUnM2Yr34xy1
    • Remove the batteries from the battery compartment by sliding the white battery compartment switch up and then move the panel toward the right.

  2. plbg3wBXVchmOYit
    • Using the Phillips #000 screwdriver, unscrew the two 2mm screws next to the battery compartment on the right side of the camera.

  3. cjj5HS2fY2rmHOc4
    • Unscrew the two 2mm screws on the opposite side.

  4. FUFQJO2lHZ2THs3T
    • Flip over the rubber AV cover at the bottom of the camera. Unscrew the last two 2mm screws on the bottom of the camera.

  5. mbhUH4h5JtFSnguc
    mbhUH4h5JtFSnguc
    UorMuemICkqeCSJq
    LcKAfOZdXRudaqdV
    • Using your hands, open the camera slightly by using the indentation above the camera compartment.

  6. uhHpxcnXpDbqxLAx
    uhHpxcnXpDbqxLAx
    cX3vCGSNCGojQK5t
    • Wedge the flat end of the spudger in between the front and back cover. Carefully push the spudger downward, which will lift the back cover off the camera.

  7. 1CxbGF35rFYMwUmS
    • Gently pull the cover off the camera.

  8. Zi6PpYgDeVaxQilW
    Zi6PpYgDeVaxQilW
    o2itbnehQMYWbQRF
    Nvp6Q5HT4LIGLWZm
    • Carefully flip over the LCD screen onto its front. Pull the top of the LCD screen toward you keeping the bottom of it inside the camera.

    • Do not pull on the LCD screen; there is a ribbon of circuitry that is connected to the motherboard.

  9. aA4M1bkpOHTGGNmW
    • Gently hold the LCD screen down, so the ribbon lays flat against the back of the camera.

  10. SSceRssojJQhsrQX
    • Gently wedge the spudger underneath the white latch and lift the latch open.

  11. EEPc1MWG1MeHFUHA
    EEPc1MWG1MeHFUHA
    GydxpTLN4dTrkKes
    • Use the flat side of the spudger to flip the white switch on the motherboard. You should hear a light click.

  12. X4wDWxfIFtWddO6b
    • Gently pull the ribbon out of the switch.

  13. Gyy2vSZNNH534m6I
    Gyy2vSZNNH534m6I
    XYVGMuLuKoHU2wki
    • Open the battery compartment door by sliding the white switch upwards. Push the door towards the right of the camera.

  14. KepAGtVGiDxaLZCw
    KepAGtVGiDxaLZCw
    EBSgpQuDyWo32W2u
    vNMMKVQwWLAiEv4X
    • Hold the camera with the lens face down to prevent the plastic covers of the warning light and the flash bulb from falling out.

    • Take a firm hold of the black inner casing of the top and bottom of internal camera. With your other hand, take a hold of the red front case.

    • With slight force, pull the internal camera upwards and out of the front case.

    Thanks i got electrocuted. You need to discharge flash capacitor with a screwdriver before touching the camera!!!

    Anonus Pidarimus -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Sadie

Mitglied seit: 16/02/15

403 Reputation

0 Kommentare