Nikon D610 Motherboard Replacement

Geschrieben von: Daniel Eagan
  • Kommentare: 1
Nikon D610 Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

40 Minuten - 1 Stunde

Einleitung

This guide will demonstrate the steps required to replace a problematic motherboard on your Nikon D610.

  1. KkJDqgFU6mSburYu

    • First, power off the device.

  2. MPJMDMXywWZNbHBH
    MPJMDMXywWZNbHBH
    vYqUQJWuRfaRydtH
    1xegEXJdIsLDfVfT

    • Set the camera so that it is sitting on its side.

    • Open the battery compartment door by sliding the release button towards the lens.

    • This will cause the door to "pop" open slightly

  3. yOCbcCgJXNJE3Zku
    yOCbcCgJXNJE3Zku
    FWmn4HlgeA4hG4CT

    • Now lift open the battery compartment door.

    • Push the yellow tab lock towards the center to release the battery.

    • This will cause the battery to jump up as there is a spring at the bottom.

    • Pull straight out, slowly on the battery.

    • Make sure you pay attention to which way the battery goes .

  4. UkkM5FMOGawDebHp

    • After removal of the battery. Pull the battery compartment door away from the lens.

    • There are eleven Philips head screws that hold the bottom cover on, including a few inside the battery compartment.

    • Remove all the screws and the bottom face should pop off easily.

  5. 351hR1EaeOX6NNmF
    351hR1EaeOX6NNmF
    jUmbNqBYEqTRIAg3
    IMJ6yCZWxqYBSxer

    • Then next step is removing the seven Philips #00 screws that hold the rear face plate on.

    • There are screws hidden in three separate spots.

    • One is under the rubber doors on the left side of the camera. the next one at the eye hole.

    • The final one involves taking off the small dial that is about half an inch to the right of the eye hole.

    • Removing this dial involves putting a spungder tool behind it and applying a gradual amount of pressure.

    There is a screw under the sticker of the dial.

    dennis tsakarisanos -

  6. JUyd4gswaU1kVjFC
    JUyd4gswaU1kVjFC
    MLOUYoWAndbBJwn6

    • The rear face plate will include the LCD display it separates from the body of the camera with a small tug.

    • Do not pull to hard otherwise you risk breaking the ribbon wire that connects the controls and the screen.

    • Once there is enough space it will be possible to gently pull the ribbon cable out of their ports.

  7. XQRjpZdByv2MgRUk
    XQRjpZdByv2MgRUk
    hbdg3kUA1DVrFMTK

    • The next piece to come off is the front plate and the red grip.

    • The front plate is held on by 2 Philips #00 screws on the front and two more beneath the flash bulb.

    • Remove the two Phillips #00 screws holding on the grip and it slides off easily.

    • After removing the screws the face plate comes off by pulling it straight off to avoid damage.

  8. waX2TNBSBptcOLnq
    waX2TNBSBptcOLnq
    XZwAHm5SYVg1VKFD

    • It is now possible to remove the last three Philips #00 screws that are hidden under the memory card slot door.

    • The screws come out and the cover comes straight off.

    • The last cover plate is the top. The top is held on by two screws located just beneath the rim of the cover.

    • The top should be pulled off very slowly. There are several electronic components that connect between the body and the top.

    • There are three wires that need to be disconnected.

  9. 1uYSvIEDb3fQfZwT
    1uYSvIEDb3fQfZwT
    OdAVDG4NUTUAuJVM

    • The rear side of the camera is where the motherboard is located. It is visible after you have taken off the rear face plate.

    • Remove the shield that protects it from static first.

    • This shield has six Philips #00 screws that are positioned around the edge of the shield.

    • After removal of the screws the shield will come free from the motherboard.

  10. mXaNm5mftGvZ1CyA
    mXaNm5mftGvZ1CyA
    4iymEUuDJgyZiLoR

    • The six screws that were removed in the previous step also hold the motherboard in place.

    • There are a few ribbon cables that connect to the motherboard to the rest of the camera with some of them hiding under other ribbon cables.

    • Be very careful when removing the ribbon wires. If they break it can cause problems with needing more repairs.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Daniel Eagan

Mitglied seit: 10/02/16

606 Reputation

0 Kommentare