Nikon D7000 Tripod Plate Replacement

Geschrieben von: Jed Chen
  • Kommentare: 10
Nikon D7000 Tripod Plate Replacement

Schwierigkeitsgrad

Moderate

Schritte

26

Zeitaufwand

30 - 35 Minuten

Einleitung

Use this guide to replace the tripod plate.

  1. cm2ORulUQgTIcLmD

    • Remove the following 5 screws securing the bottom cover to the camera body:

    • Four 6 mm J000 screws.

    • One 8 mm J000 screw (under lens mount).

  2. QrvtqxRGqmKLmUBP

    • Remove three 6 mm J000 screws from under the battery cover.

  3. 1GCOjoFZbEViDOW4
    1GCOjoFZbEViDOW4
    PJGgX3SaLO4TUbMl

    • Gently pull the bottom cover off of the camera body.

  4. XVgnRPoHTfHutPvM

    • Remove the following screws from the port area:

    • Two 3.5 mm J000 screws.

    • One 6 mm J000 screw (right above ports).

  5. HkWQ6gc1GHGvddu4

    • Peel the rear rubber piece off with tweezers.

    This is not needed : if you don't touch this rubber & screw the SD card cover will come off at the same time that the back case.


    = Quicker and easier

    Xavier -

  6. 6XxLbBTXnoWYi1Ge

    • Remove one 4.25 mm J000 screw from behind the rear rubber piece.

    This is not needed : if you don't touch this rubber & screw the SD card cover will come off at the same time that the back case.


    = Quicker and easier

    Xavier -

  7. TEv5KiI1DkUae1PV

    • Pull the eyepiece cover up to remove it.

  8. kmD2nMN41RJFCpFK

    • Remove two 6 mm J000 screws from behind the eyepiece cover.

    • On D7100 models, there is an additional screw holding the back plate on. This screw is located in the diopter (dial with + - on it). This screw can be accessed by peeling up this sticker on the diopter.

    Concerning the diopter, it's wrong : D7000 also have a screw in it.


    See step 41.

    Xavier -

  9. xDPUe1oxYB1bm3KO

    • Open the SD card cover by pushing slightly down with your thumb and sliding up.

  10. vLRVX4NIPSFASgd1

    • Remove four 6 mm J000 screws that secure the SD card cover.

  11. nMT4dsBPdeK6J21C

    • Gently pull the SD card cover off.

    Attention! High voltage. After removing the memory card cover, remove the yellow sticker and use a 220 volt 15 watt incandescent lamp to discharge the capacitor.

    Rust Twentyone -

  12. EWyUIHjVmBVOgqYS

    • Remove the following screws that secure the back case:

    • One 6 mm J000 screw.

    • One 3 mm J000 screw.

  13. pNJYwvZBCDlCCpZi

    • Carefully lift the back case off.

  14. lh3Oft4G2DQp6i2E
    lh3Oft4G2DQp6i2E
    FXEpWEbpTIw1UJYn
    aTqIKEtXXMoEpEf4

    • Disconnect the following two ribbon cables from the motherboard.

    • See our Cable Connector Guide for help with ribbon cable connectors!

  15. hiVpQMmmHvQwywQT
    hiVpQMmmHvQwywQT
    jaHEmXKNNr2MMIgV

    • Remove the following screws securing the left motherboard shield:

    • One 2 mm J000 screw (on the bottom).

    • One 3.5 mm J000 screw (on the back).

    • Be careful of the grounding clips on the motherboard.

  16. fK2lsUZIQM6RHB4T

    • Gently pry and lift the left motherboard shield off.

    No need to remove shield. Risk of damaging clips holding shield.

    Ziyang -

  17. nTEWTNAKao3GrCri

    • Remove one 3.5 mm J000 screw securing the right motherboard shield.

    No need to remove shield. Risk of damaging clips holding shield.

    Ziyang -

  18. NNACDft5njSv6EL4

    • Gently lift the right motherboard shield off with the tip of a spudger.

  19. wgv453L4WEkbAppj
    wgv453L4WEkbAppj
    HBMtgXGXO32h4rxn
    uYtnEvYSojhopC2Q

    • Disconnect remaining ribbon cables.

  20. vrKgmlOCkQZsnoSR
    vrKgmlOCkQZsnoSR
    tLGYNWDruWlMGiho

    • Disconnect remaining ribbon cables.

    One more ribbon behind press down tab

    Ziyang -

  21. bPYkPsiLyFvMgpFg

    • Carefully disconnect the red connector with tweezers.

  22. 4Iurv4DleT5RAXaJ

    • Remove four 3.5 mm J000 screws securing the motherboard.

  23. FbPCIAVSAoAmHKEy

    • Gently pull the port side cover away from the motherboard.

  24. 5aopPFIduUGoVfRG

    • Lift the motherboard off.

  25. D6B3TYP6DEBnulQZ

    • Remove four 6 mm J000 screws securing the tripod plate.

    Only left 2 screw need to be removed. The tripod plate do not need to be removed.

    Ziyang -

    Actually, nothing needs to be removed !

    Skip this step and gain time and energy :)

    Xavier -

  26. ZQP4OJa5LfGHp4pC

    • Carefully lift the tripod plate from the backside of the camera and slide out the grounding clip from under the lens mount.

    Skip this step (see comment step 25)

    Xavier -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jed Chen

Mitglied seit: 02/04/15

1796 Reputation

0 Kommentare