Nook BNRV300 Motherboard Replacement

Geschrieben von: Alisyn Waite
  • Kommentare: 6
Nook BNRV300 Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

9

Zeitaufwand

10 Minuten

Einleitung

This guide describes the removal of the motherboard from the Nook BNRV300 device. This device is also called the “Nook Simple Touch.”

Removing the motherboard allows access to the display and the plastic front cover frame. Removal of the motherboard also enables you to work on electrical components.

Warning: Using metal tools on the motherboard or any electrical components could cause shock to yourself and/or your device. Using plastic tools reduces this risk, but pay attention when working on your device.

  1. 4hayZ5Ht1AZBvCt6
    4hayZ5Ht1AZBvCt6
    KGscQOogjjtO1XKb
    bkJVnQCeriyUtCDo

    • Power off your Nook before working on your device. Hold the power button for about 5 seconds and select the “Power Off” option.

    • Turn the Nook over to find the power button along the back upper edge.

    • Wedge the spudger between the top of the power button and the upper edge of the device.

    • Push the tool down to pry the button up and off.

    You should pull up from the bottom of the button. It will hing up and pop off easier and less chance of breaking the button. There is a hing on the top side of the button to pivot down to the bottom where the button is. The clips are near the bottom of the button. You are more likely to break the pivot pins doing it from the top.

    dl200010 -

    Thanks for your input!

    Emily Tracy -

  2. 5LaMcJILWcVkUein

    • Using your fingers, take off the power button.

  3. MXsJU1XKOYCmUya2
    MXsJU1XKOYCmUya2
    BqmedEd3VQEGXHMa
    WvhohJAmPTfJUaYO

    • Peel off the white sticker that is covering the screw head.

    • Remove the one 2mm-long screw using a size T5 Torx screwdriver.

  4. SxWR1BYqOpqmYmCI

    • Wedge an opening tool between the back cover and the front plastic border at the top of the device (near the power button).

    • This will require some force.

    • Slide the opening tool along the edges of the device, prying up until you are able to use your fingers to remove the back cover.

    • The back cover snaps as it pops off. This is normal.

    There is no need to pry the cover off. Just slide the back cover down toward the USB port.

    Young -

    This right here! It requires little to no force to do this. You are more likely to break the clips if you force it open.

    dl200010 -

  5. wtxknhD24PALYUU4
    wtxknhD24PALYUU4
    2M4pUPKj4X2UKJKG
    kCaxT2QrmrjsDaAJ

    • Use a spudger or your fingers to gently pry the connector out of the white socket.

    • The back cover is now fully detached.

  6. 2ukpkDsQVQckbbXM
    2ukpkDsQVQckbbXM
    M6QDVq2l1DTbLA3v

    • Use tweezers to remove the brass-colored threaded fastener from the Nook plastic casing.

    There’s absolutely no reason to do this. This part of the device is never touched again for the rest of the guide.

    James Beegle -

  7. 6cjNUILOQhyS6RLB
    6cjNUILOQhyS6RLB
    SCuVmml5pMfU5M1s

    • Use an anti-static mat to prevent electric shock from damaging the motherboard and its components. Be careful when using metal tools on your device.

    • Using a T5 Torx screwdriver, remove the eleven 3mm screws.

  8. 55uHPkAscTAPHPt4
    55uHPkAscTAPHPt4
    CJseMZHkPUlfiekt
    QJYpkx2aQmFEfGkp

    • Place the spudger through the loop of the display cable. Lift the tool up, which will unhook the display cable.

    • Do not put force on the motherboard with the spudger. This could damage components on the motherboard.

    • Using your fingers, lift up the display cable.

  9. QSfqHX3BGoCaCVtR

    • Using your fingers, gently lift the motherboard from the display.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alisyn Waite

Mitglied seit: 03/10/19

375 Reputation

Ein Kommentar

Check the comments on each step. There are some adjustments to the process to properly and safely take this apart.

dl200010 -