OLPC XO-1.5 Screen Replacement

Geschrieben von: Andrew Ferrell
  • Kommentare: 0
OLPC XO-1.5 Screen Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

20 - 25 Minuten

Einleitung

This guide will show you how to access the screen on your OLPC XO 1.5.

  1. 5JZujLyxqZ5YkfZv

    • Place the laptop upside down with the handle away from you.

  2. JqKAjkWlGoNU32XI

    • Slide the tabs out, towards the green edges, to show the open lock symbol.

    • The right tab will stay in place, but the left tab must be held in position while you remove the battery.

  3. bsBtmQOI1WCAMVhB
    bsBtmQOI1WCAMVhB
    1IMB3qOYwcSJJqFD
    fRqOjNwNPttV2o1B

    • Lift the middle of the battery to remove it.

  4. PG1OSFAoP1wxYxMk
    PG1OSFAoP1wxYxMk
    XNnQxNujR6rbyym6
    iumOWCRCgtO3c5cm

    • Turn the laptop so it is resting on its bottom.

    • Open the laptop by rotating the green wings on the side up, then lifting the top half of the laptop.

    • Rotate the top half of the laptop about 90 degrees.

  5. 2YiXDZwTUVSMUYPQ
    2YiXDZwTUVSMUYPQ
    3VYImrlbWoNsUCLL

    • Turn the laptop upside down, so you can see the screws on the bottom of the top half.

    • Remove the two 4mm screws with a Phillips #1 screwdriver.

    • Rotate the top half 180 degrees.

    • Remove the two 4mm screws with a Phillips #1 screwdriver.

  6. ujq2iJGuCxBgPoQu

    • Rotate the top of the laptop 90 degrees, so that it is facing you again.

    • Slide the green pieces off the device. They should come off easily.

  7. fOVio1MNgtpxiGMG
    fOVio1MNgtpxiGMG
    yTvYb2EkXsUuBy34
    qpSHpwFFiVZmFMVQ

    • Pull down on the white screen cover. It does not require much force.

    • Remove the screen cover.

    • The game pad on the left sometimes falls during this step.

  8. BbuHw3D5gm1qkbiV
    BbuHw3D5gm1qkbiV
    qRDhoQXMxDjkj3SS

    • Unscrew the four 7.62mm Phillips #1 screws on either side of the screen.

    • The screen is still connected by ribbon cables. You can damage the cables if you remove the screen before disconnecting the cables.

    • Move the screen down a little to expose the ribbon cables.

  9. Ww4Ko2yruZILCHYD
    Ww4Ko2yruZILCHYD
    2j6lWrbH3gTHVxSU
    OKVZ55kY6nuH3KyP

    • Flip up the tab right under the middle top of the screen.

    • Pull the black ribbon cable out of the socket.

  10. K4ova12yB1qD56Pi
    K4ova12yB1qD56Pi
    IRDZ4rUX2roaBLGX

    • Flip up the smaller tab under the left side of the screen.

    • Remove the small cable to separate the screen from the rest of the laptop.

    • Gently remove the screen.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Andrew Ferrell

Mitglied seit: 05/10/12

27 Reputation

0 Kommentare