OLPC XO-4 Touch Back Cover Replacement

Geschrieben von: Matthew Smith
  • Kommentare: 0
OLPC XO-4 Touch Back Cover Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

15 Minuten

Einleitung

Use this guide to access the back cover of your OLPC XO 4.0 Touch.

  1. IVDjFWXGlqHFaVWw

    • Turn the laptop upside-down, with the handle facing away from you.

  2. d5MasQwOp11X2VZr
    d5MasQwOp11X2VZr
    sRU3hllA2YskCHfU

    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

  3. ZWV1wud4mI1HUWGt
    ZWV1wud4mI1HUWGt
    UnbfciGCtddNpqAL

    • Lift up on the middle of the battery to remove it from the device.

  4. ZNwppNTdPuVCNHlb
    ZNwppNTdPuVCNHlb
    PdDWKtkFVQFMB64Y
    XJm6YIlG5kYTADAK

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

  5. I1Z2kk1JF2L4WZHc
    I1Z2kk1JF2L4WZHc
    Nx2miaLWtnYXwsBB
    SXaNNPsDjPeOS2qY

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

  6. MDDSedKaPcB4QX4L

    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

  7. pXcPMs3Be4Hd1snY
    pXcPMs3Be4Hd1snY
    ZVcYoG1MdgEQixp4

    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

  8. EfZ4UtuOt5IRVxX4

    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

  9. gEQt5gmm1JkSjGxl
    gEQt5gmm1JkSjGxl
    KydMhVUsYnjxuBdg

    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

  10. EIf6RsDWwSGSDelj
    EIf6RsDWwSGSDelj
    WmGEwThaynJIeKOf
    3tpoOnmk1RYPgAHH

    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

  11. xU51FJdqQjVvqZOl

    • Remove the screen from the laptop.

  12. FMeimEIATXZCvDdW

    • Remove the four 6mm screws using a Phillips #1 screwdriver.

  13. tEvhDv6C4oD1l1kM
    tEvhDv6C4oD1l1kM
    eYR4sicGWZpuKZxc

    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Matthew Smith

Mitglied seit: 25/01/13

23 Reputation

0 Kommentare