One Education Infinity:One Motherboard Replacement

Geschrieben von: Taylor Bratsch
  • Kommentare: 0
One Education Infinity:One Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

11

Zeitaufwand

35 - 40 Minuten

Einleitung

This guide will demonstrate how to replace the motherboard in your One Education Infinity:One laptop.

  1. kLKwDj2aHVagP5Mg
    kLKwDj2aHVagP5Mg
    33FbsZ1kP56Uhl43

    • Use a spudger to disconnect the black bundled cable connector from the motherboard.

  2. kOi3RhLhuLBFkGoV
    kOi3RhLhuLBFkGoV
    AJludX4VhiOctykA
    SVLNiUhhv5KfEyDB

    • Use a spudger to lift the black tab on top of the ZIF connector.

    • Slide the ribbon cable out of the connector.

  3. 6TMAWcUXDS3hbJNe
    6TMAWcUXDS3hbJNe
    V6DXuayK2kH1ZVt2
    mIXPEPIdhpgEmltj

    • Use a spudger to flip up the black retaining flap on the ZIF connector.

    • Pull the folded ribbon cable straight out of the connector.

    • This ribbon cable must be disconnected before removing the battery because it is attached to the battery with adhesive.

  4. HHywNc2uwuE1KqUN

    • Use a spudger to pry the battery away from the device.

    • Always use ESD safe tools when working with delicate electrical components.

  5. PAEEOhwlBtlqdHhT
    PAEEOhwlBtlqdHhT
    NZOkEllDXUB5YxCS

    • Use ESD safe tweezers to disconnect the antenna from the motherboard.

  6. bBCCLLTsH1EVcUaL
    bBCCLLTsH1EVcUaL
    gUDVwHLHmTbwnuFU
    Oe3jeYGcjcEEDb5F

    • Use a spudger to flip up the black flap on the camera's ZIF connector.

    • Pull the ribbon cable straight out of the connector.

  7. YJHXOOBtJjV4TDRB

    • Use tweezers to pull the dock connection cable away from the motherboard.

  8. Kf1yePQmnNAFoIJF

    • Use a Phillips #00 screwdriver to unscrew the two 3.4 mm screws.

    • Use a Phillips #000 screwdriver to unscrew the one 4.2mm screw.

  9. jBIVQXFkCU6qlUhn

    • Lift the protective shield away from the motherboard.

  10. tV3ACHBw5eZfQdoN
    tV3ACHBw5eZfQdoN
    LcM4NamCQXyRYIGF
    EwJiIqUbh3g5GA4K

    • With the flat end of a spudger, flip up the black flap on the display's ZIF connector.

    • Insert the pointed end of the spudger between the cable and the motherboard and gently pull the cable straight out of the connector.

    • During reassembly, be sure to insert the cable into the connector up to the white line on the cable and then close the retaining flap.

  11. QjkJdsfwkTlpLwFx

    • Gently lift the motherboard away from the display assembly.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Taylor Bratsch

Mitglied seit: 06/09/16

5504 Reputation

0 Kommentare