PS Vita Slim Motherboard Replacement

Geschrieben von: Daniel Woodard
  • Kommentare: 6
PS Vita Slim Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

8

Zeitaufwand

15 Minuten

Einleitung

Note::: taking apart your device may void the warranty on the device, please proceed with caution and consider having it sent in first if possible to be worked on by the company. This guides goal is to help you replace your motherboard if anything is currently wrong with it. As long as you take your time and you are careful you should be able to complete the replacement process with any problems.

  1. MWUymU6oT1rGeD6u

    • Taking apart your device may void the warranty on the device, please proceed with caution and consider having it sent in first if possible to be worked on by the company.

    • Please make sure the system is completely powered off and all SD storage cards are removed before starting the removal process

    • All 6.35mm screws were removed using a J00 bit from the iFixit pro toolkit.

    • There are four screws on the back of the device, remove them as shown.

    I actually broke a 32GB storage card because I didn’t remove it first before I open the chasis. Beware of this!!! REMOVE YOUR CARD FIRST!!!

    Daniel Wang -

  2. dNixpdkvqXrEXvRX
    dNixpdkvqXrEXvRX
    6FOyLDiaHJn3JbMJ

    • There are two screws on the bottom, near the charging port, remove them using the J00 screwdriver on the 6.35mm screws from the iFixit pro toolkit.

    • Finally, remove the top screw under the dust cover using the J00 screwdriver on the 6.35mm screws from the iFixit pro toolkit.

  3. oB5eopNayEQgQNdm
    oB5eopNayEQgQNdm
    AFU4gg4k5bwrPruG
    JjhdMGePJxTZe1sZ

    • The next step will require the opening tool.

    • Please carefully separate the back from the front completely. You will need to disconnect the small ribbon cable on the inside before completely removing the back. Otherwise you may end up hurting the ribbons on the inside.

    • While separating the back, carefully pry all the way around the back. You will hear popping noises while going around and this is a good sign.

    • Upon removing the back panel you will need to slowly and carefully remove the ribbons connecting the hardware to access the needed parts to be repaired.

  4. nQrlvZtdJYWOSKtU

    • Once the ribbons have been removed, then the back is fully removed and you can access the hardware within.

    Don’t forget to remove the battery at this point. The little corners of the connector that poke out a bit are there for you to pry the connector up. Be careful pulling the battery connector out by the wire, you could damage the wire where it is attached to the connector.

    Landon Burnette -

  5. TY5plT4axJ5vP4LY
    TY5plT4axJ5vP4LY
    BdMdFigOHADHehZe

    • First you will want to remove the black casing holding the motherboard in.

    • Remove the two screws that are holding the casing down. These will be 6.35 mm screws that are to be removed using the J00 bit from the iFixit pro toolkit.

    • Once the screws are removed, carefully lift the case out of the system.

    There may be three screws holding the casing in. One between the two shown but up a bit higher. You can see the hole it should be in in the picture.

    Kiev -

  6. tepipoAVaUflvvQE
    tepipoAVaUflvvQE
    gidGTLQCVvo1sPlo

    • Next remove the two bottom 6.35 mm screws using the J00 bit from the iFixit pro toolkit.

    • Now you will be able to gently remove the bottom casing.

    There are tabs on this piece too. On the far right and far left. I believe there is one in the middle but I was able to pull it out with enough force that that one did not seem to matter.

    Kiev -

  7. 3aDAIopN2iwWtSCd
    3aDAIopN2iwWtSCd
    EYUiBRYW3jZDL2iQ
    roo1jRstQkjGLKFs

    • Next you must remove the two ribbon cables connecting the motherboard to other hardware parts. Please be careful. The third ribbon on the bottom is a camera that also needs to be carefully removed.

  8. n52Z5fkOLfvKcrVu
    n52Z5fkOLfvKcrVu
    ZNLXsaCQGbkN4xKn
    4CD6PCosCy6lVMQY

    • Now gently lift the motherboard up, as there will be a ribbon that still needs to be removed.

    • Carefully remove the last ribbon, from the hardware and not the motherboard.

    • The motherboard can be successfully removed.

    • Any repairs or replaces will be doable now.

    There will be clamps connecting this piece to the shell. Remember to pull them back instead of brute forcing it if it is not coming out.

    Kiev -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Daniel Woodard

Mitglied seit: 23/08/17

2449 Reputation

Ein Kommentar

bonjour ma ps vita slim

batterie changé et la console a du mal a demarré quand elle s'allume comme si c'est comme elle a pas de batterie se remet a zero et apres on lance un jeu elle s'éteint et quand elle redémarre remettre heure c'est quoi le probleme

merci

Raymond Depardieu -