PSP Go Battery Replacement

Geschrieben von: Miroslav Djuric
  • Kommentare: 8
PSP Go Battery Replacement

Schwierigkeitsgrad

Moderate

Schritte

8

Zeitaufwand

15 Minuten

Einleitung

This guide shows how to remove the PSP Go's battery.

  1. LhA1YVTFVpuSaY5i
    LhA1YVTFVpuSaY5i
    iqxlosSvmM4KTYNl

    • Unscrew the four Phillips screws on the back of the PSP Go.

    • Rotate the PSP so you can see the top of the device.

    • Unscrew the two Phillips screws next to the volume buttons.

  2. nMEVBYIvPaGa4lSm
    nMEVBYIvPaGa4lSm
    g3JkOmU5wiX4ln1G

    • Use a plastic opening tool around the perimeter of the back cover to loosen it on all sides.

    • Open the back cover by gently lifting the right side, and rotating it to the left side (as if you were opening a book).

    • Be careful not to rotate the back cover from the bottom, as you will break the plastic screw holes on top of the device.

  3. ABedZDx5FKLfOJIa

    • Pull the top cover upwards gently from its housing.

  4. LYVuWJyvdtFkk4JT

    • Use a plastic opening tool to gently flip up the left trigger connector.

  5. RobBtNiafm4CbktD
    RobBtNiafm4CbktD
    ai22jrpUUL31uFil

    • Unscrew the lone Phillips screw holding the trigger in place. Remove both trigger and retaining plate from the PSP Go.

    • If necessary, repeat steps 2 and 3 to remove the right trigger button.

  6. POB2kIU1pC2bAZwB
    POB2kIU1pC2bAZwB
    Df2WURdcRVxMLqXS
    oSaHUIa4F1hBAhLf

    • Do not peel the sticker away from the left EMI shield. It will expose the "VOID VOID" lettering that will void your warranty!

    • Use the plastic opening tool to gently peel away at the "Warranty Void" sticker. Start on one edge, as shown, and slide the tool from side to side until the sticker is removed from just the battery.

  7. W3RaNQ4ROUC4Ie6o

    • Gently pull the sticker away from the battery connector, just enough so that the connector is visible.

    • Wedge a plastic opening tool in between the connector and logic board, and gently pull the connector upwards.

    • Make sure not to disconnect the white connector socket on the logic board, and just the connector itself.

  8. UbWivVTYavbCgmCV
    UbWivVTYavbCgmCV
    MkMNyMnRSZEhe2JF

    • Use a plastic opening tool to pop out the battery, being careful not to snag the "Warranty Void" sticker in the process.

    • When putting a new battery into the PSP Go, make sure you hold the "Warranty Sticker" so you don't put the battery on top of it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Miroslav Djuric

156735 Reputation

8 Kommentare

this was so quick . I have been trying to get this repaired for years, only to hear throw it away there is no fix . sharing love

mainemade4u -

a couple of notes my cover came completely off in the beginning step without a problem or broken screws. next i didnt und the wired cabled beside the clicker and it wasnt in the way.

mainemade4u -

After replace a new battery my psp go going crazy. Charge only 1 or 2 min led going to green but not fully charge. Anyone can help me to fix this

Mus Mohamed -

Cfw 6.61 pro update. Helppp

Mus Mohamed -

Thanks to this guide I was able to reseat the battery, the PSP was not turning on or charging any more, now everything is working again.

Marvin Arand -

Excellent guide, PSP go works like new!

Ryan Solusod -

I bought a replacement battery online for my PSP Go, but it came without the white connector. Have you an idea how to fix it?

anibaal.d.jiraiya -

My psp go is not charging but when I connect it my laptop is get connected any idea what is going on

dawooddjmax -