Removing Olympus FE-210 Motherboard

Geschrieben von: Alex Wolff
  • Kommentare: 0
Removing Olympus FE-210 Motherboard

Schwierigkeitsgrad

Difficult

Schritte

14

Zeitaufwand

15 - 20 Minuten

Einleitung

Before removing the Motherboard you must first remove the LCD Screen.

  1. kOvDTMFpOTGOStDJ
    kOvDTMFpOTGOStDJ
    Nuqe5bDwjKLmoVHK

    • The battery compartment is located on the bottom side of the camera. Push the button in, and slide the cover to get access to the batteries.

  2. ZxDN3K3hyTgvRvcK
    ZxDN3K3hyTgvRvcK
    wsGTdrCIvwowmIhh

    • The batteries will slide right out.

    • When putting new batteries in, make sure they are pointing the right direction.

  3. QTG24NZNnPMtjEUx
    QTG24NZNnPMtjEUx
    6D5PieSOFZrdWTBq
    shaCqQuDKpQBitWU

    • Remove the 7 screws holding the front case in place, with a #00 screwdriver.

    • Six screws are 3.6 mm.

    • The seventh screw is 3.2 mm.

  4. YF6x1BMOOIBUQGe2
    YF6x1BMOOIBUQGe2
    tRqkWaMDI2HQUXOc
    FWYixyCSqlGcMJnL

    • Pulling the front case off, requires applying enough strength in the right areas.

    • The front case snaps into place in three places:

    • At the top and bottom of the battery side (opposite of side pictured) of the case.

    • Right in the middle of the DC-in side (side pictured) of the case.

    • Top of the camera, to the left of the power button.

    • Once those places are disconnected, the front case will pop right off.

    • The camera in the first two pictures is upside down. This is the best position to place your thumbs to remove the case.

  5. 1tWeFSQXUwroXViL

    • Remove the 3.2 mm screw in the battery compartment using a #00 screwdriver.

    • After removal of the screw the case will be loose, but do not tug it off. There is a cord connecting the rear controls to the motherboard.

  6. DBA1PkBHibHc1OUm
    DBA1PkBHibHc1OUm
    cIsDJRFKfEYBCv4R
    npYESMXiQalacGtK

    • Carefully pull the rear case away from the camera until you have access to the cord connected to the motherboard.

    • Lift the white latch using a fingernail or a spudger.

    • Pull the cord from its connector.

  7. ekflxZhApPdIMDDV
    ekflxZhApPdIMDDV
    GSUaOVS2cXniYATg

    • Remove the two 2.7 mm screws using a #00 screwdriver.

    • After removing the screws the display will be free. Do not remove it. Like the rear case, there is a cord connecting it to the motherboard that must be disconnected first.

  8. yyF1ZTNHFGAIyLwi
    yyF1ZTNHFGAIyLwi
    jXZ1tZFV6HPTd3UF
    InVkMOJRBbLdpFBU

    • Using a spudger, lift the latch on the connector.

    • Remove the ribbon cord from its connector.

    • Remove the LCD from the rest of the camera.

  9. OGmnpVvvsWMCEHqW
    OGmnpVvvsWMCEHqW
    jGdYJFC5HaBKTIRe

    • Remove the 2 pieces of translucent yellow tape.

    • Removing these pieces of tape will void the camera warranty. They serve no functional purpose and do not need to be replaced during reassembly.

  10. KdkNHdK3MpNViM4e
    KdkNHdK3MpNViM4e
    wTFniYOxwnEmSUwp

    • Remove the seven 2.7 mm using a #00 screwdriver.

  11. fDuwDg5YaGDDueDJ

    • Remove the ribbon cord located near the top right corner of the motherboard. Do this by carefully pulling the cord out of the socket using a pair of tweezers.

  12. OqPSLe1xIGRpGZn1

    • Disconnect the ribbon cord located on the left side of the motherboard.

    • Use tweezers or a spudger to lift the latch on the connector.

    • Carefully remove the cord from the connector.

  13. c1lCECRFnNpSSZtD
    c1lCECRFnNpSSZtD
    dAeWDVFTUEK156pS

    • De-solder the 2 connection points.

    • Be careful to not damage any part of the circuit board with the soldering iron.

  14. a1GBJSPsQXhicYA4

    • Remove the motherboard from the camera casing.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alex Wolff

Mitglied seit: 21/01/11

234 Reputation

0 Kommentare