SONY ZS-BTG900 Disassembly

Geschrieben von: Alfredo Rodriguez
  • Kommentare: 3
SONY ZS-BTG900 Disassembly

Schwierigkeitsgrad

Difficult

Schritte

11

Zeitaufwand

30 - 45 Minuten

Einleitung

This guide is going to show you how to open and disassemble the Sony ZS-BTG 900. By the end of the guide you will have three main areas of the device standing the alone. The three areas will be: the top, the base, and the front.

  1. 2YdXvWrhLnuHTZDs
    2YdXvWrhLnuHTZDs
    1BKu5FIxHqOJ1VUK

    • Lift up the handle to reveal the screws.

    • Use your Phillips #2 screwdriver to remove the eight 1/2 inch screws.

  2. OYVF11Stopn2bywJ
    OYVF11Stopn2bywJ
    wlRMsmsokxGPp63m
    EEdbbG4PrXKuGMTF

    • Flip your device over.

    • Use your Phillips #2 screwdriver to remove the six 3/4inch screws.

    • In removing the screws within the two holes on the back of the device, you may want to use your shaft extension to provide extra torque as they may be very tight.

  3. hLHpoLpRnu53btsY
    hLHpoLpRnu53btsY
    Z6ljgpIaE1uPl6G6

    • Flip your device back over to access the top of the device.

    • Use your plastic opening tool to pry up and remove the panel on the top, left hand side of the device.

    • This will reveal two additional screws.

  4. NQo1wYjtupTeABrL

    • Use your Phillips #2 screwdriver to remove the two 1/2 inch screws underneath the now-removed panels.

    How do you remove the carrying handle

    Gerald Senchak -

    Seems the handle has to come off before the top….. how does the handle get removed? Thanks!

    Dan Mull -

  5. FgIkJSDGhrRCMoiF
    FgIkJSDGhrRCMoiF
    1JA2buRdgN5XHraU

    • Lift off the top, beginning from the back of the device.

    • Take care when lifting the top portion as there are many wires connected to the inside of the device and you do not want to disconnect these just yet.

  6. Q1Sq3uC6trtQjlUP
    Q1Sq3uC6trtQjlUP
    i2tIjlEk3RSvGWKg

    • Disconnect the CD drive ribbon cable from the top of the device.

  7. TyZSWnfEL1EWJ5Av
    TyZSWnfEL1EWJ5Av
    Kt2WGwlodqUJGv3F

    • Disconnect the antenna cables.

  8. GSne6jipRubSerfT
    GSne6jipRubSerfT
    PZOnwcvSmaouXoer
    DrTAf443HC2WxPkh

    • Disconnect the remaining cables from the motherboard.

  9. aaXAeDPQj66ZF5FT
    aaXAeDPQj66ZF5FT
    yAvH2PIRiVXqQHBf

    • Once you have removed the top, we will begin removing the front of the device.

    • Begin by disconnecting the 6 cables that lead from the front of the device to the motherboard.

  10. IHkd5EZ3xKN34nBS

    • Use your Philips #2 screwdriver to remove the two 1 inch screws on the outermost part of the device.

    • Use your Philips #2 screwdriver to remove the two 3/4 inch screws on the outermost part of the device.

    • Use your Philips #2 screwdriver to remove the one 5/6 inch screw on the middle part of the device.

  11. HLoB5awUX543xpGD
    HLoB5awUX543xpGD
    ui3vwXv5py3Ed1Kd

    • Firmly pull off the front of device.

    • There will be a small amount of black glue. You can simply ignore this, and continue to pull, or use a sharp edge to cut the glue once you've revealed it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alfredo Rodriguez

Mitglied seit: 11/04/16

969 Reputation

Ein Kommentar

Alfredo and any others who developed this guide - you are awesome! Thank you very much for the great level of detail. Saved me a bunch of time.

Mike L -