Samsung Galaxy A32 5G Back Cover Replacement

Geschrieben von: Dominik Schnabelrauch
  • Kommentare: 2
Samsung Galaxy A32 5G Back Cover Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

15 - 25 Minuten

Einleitung

Use this guide to replace a damaged back cover on your Samsung Galaxy A32 5G.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. YFuWdcMkdDwISO4V

    • Prepare an iOpener and apply it to the back cover for at least two minutes to loosen the adhesive underneath.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

  2. gJda3ZWaNnGrBV4Z
    gJda3ZWaNnGrBV4Z
    SluTT2QUXBrIEiTn
    Twc1RWDfZBysrNIe

    • Secure a suction handle to the bottom edge of the back cover, as close to the edge as possible.

    • If the back cover is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the back cover with the suction handle to create a small gap between the back cover and the frame.

    • In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Insert an opening pick into the gap you created.

    • Slide the opening pick to the bottom right corner to slice the adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  3. Sbm41JwyBEbOeQOR
    Sbm41JwyBEbOeQOR
    MNIWVWgliRkMFg1L

    • Insert a second opening pick at the bottom edge of your phone.

    • Slide the opening pick to the bottom left corner to slice the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  4. DD62PxSptCTcQJbw
    DD62PxSptCTcQJbw
    MXFyZygkagBNRJJ4
    wTIZKAIdbq4miMNV

    • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener for one to two minutes to reheat it.

    • Insert a third opening pick at the bottom left corner of your phone.

    • Slide the opening pick along the left edge of your phone to slice the adhesive.

    • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

  5. qUSMoIlJRnfw2PXy
    qUSMoIlJRnfw2PXy
    eMfMLMoZW5TSCYBG

    • Insert a fourth opening pick underneath the top left corner of your phone.

    • Slide the opening pick along the top edge to slice the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  6. PbfBGQ1FCOr1LyVI
    PbfBGQ1FCOr1LyVI
    eSblSQRVj6KQToLI

    • Insert a fifth opening pick underneath the top right corner.

    • Slide the opening pick along the right edge of the back cover to slice the remaining adhesive.

  7. jIfeiZ1vDDXpeVGu
    jIfeiZ1vDDXpeVGu
    JVwoRt2hxQtQcftF

    • Remove the back cover.

    • Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

    • Secure the new back cover with pre-cut adhesive or double-sided adhesive tape. After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Tinte & Feder

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167866 Reputation

2 Kommentare

What? Where is the rest of this Manual? There's more to a screen replacement then taking the old screen off? There is also components that still need to be swapped over like the Mother board, the Charge Port, the Cameras etc....

BP 674 -

It is only for taking off the BACK. THERE IS ALSO A GUIDE FOR SCREEN REPLACEMENT.

Poli Poli -