Einleitung

Use this guide to remove the back cover and the fingerprint sensor on your Samsung Galaxy M31.

You’ll need replacement adhesive to reattach the fingerprint sensor when reassembling the device.

  1. CUFMfuOLGUMOJbQb
    CUFMfuOLGUMOJbQb
    RSPK3OjRPBoUWPwe
    TWAXoQmdefBwQPeF
    • Insert a SIM card eject tool, a SIM eject bit or a straightened paper clip into the hole on the SIM tray located at the left side of the phone.

    • Press firmly to eject the tray.

    My phone is restarting alone automatically what can I do please

    Oussama Laghezal -

  2. uWaHXIZWK42QenGE
    uWaHXIZWK42QenGE
    LAnecJCHKiALg4VM
    k4Ud5D1gRnuEvw1g
    • Insert an opening pick between the phone assembly and the back cover at the bottom edge of the phone.

    • Slide the opening pick around the bottom right corner to release the clips holding the back cover in place.

  3. hKYSlCA5YNwFAanO
    hKYSlCA5YNwFAanO
    N4KgcFcCYDallpBj
    • Insert a second opening pick between back cover and the phone assembly at the bottom edge of the phone.

    • Slide the opening pick around the bottom left corner to release the plastic clips holding the back cover in place.

  4. 4qebEjKmvfsg5Tc4
    4qebEjKmvfsg5Tc4
    iSd66nU5HAKMWhuT
    • Slide the opening pick along the left side of the phone to release the plastic clips on the left side of the back cover.

  5. wldaB42utZRLkXc5
    wldaB42utZRLkXc5
    TjbFrl4WUBrnki6r
    • Slide the opening pick along the right side of the phone to release the plastic clips on the right side of the back cover.

  6. wD1yufSTYpBZgYCB
    wD1yufSTYpBZgYCB
    ZSQ2HDipWYiWovx2
    LshKtxD1V1UVBxSE
    • The flex cable of the fingerprint sensor is very short and the sensor is likely to disconnect itself during the following removal procedure. Avoid damaging the cable by removing the back cover too quickly.

    • Carefully lift the phone assembly out of the back cover.

    • During reassembly, this is a good point to power on your phone and test all functions before reinstalling the back cover. Be sure to power your phone back down completely before you continue working.

  7. MxcRKiYWR4UJkdGC
    • Apply a heated iOpener to the back of the phone where the fingerprint sensor is located to loosen the adhesive underneath. Apply the iOpener for at least two minutes.

  8. lJUbrcqM2ZAWGBfu
    lJUbrcqM2ZAWGBfu
    sXcnANiGQjHnYaag
    O5kdXpfPcfpaoJYR
    • Slide an opening pick underneath the edge of the fingerprint reader.

    • Slide the opening pick around the edge of the fingerprint reader to cut the adhesive underneath.

  9. 6GKTLZXi4CZGjb3m
    6GKTLZXi4CZGjb3m
    MpGh2NHpAOyDWbTQ
    • Remove the fingerprint reader.

Abschluss

To reassemble your device, follow these instructions in reverse order. Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

Secure the fingerprint sensor with pre-cut adhesive or double-sided adhesive tape during reassembly.

Removal didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167812 Reputation

2 Kommentare

What type of adhesive is best to use to stick the back cover back on. Glue or tape?

legga001 -

лучше если останется заводской скотч.

если вы его убрали то используйте 3m скотч.

если вы заклеите на клей то потом крйне сложно будет отклеить заднюю крышку.

Сервисный Центр ПК-Партнер -