Samsung Galaxy Nexus Motherboard Replacement

Geschrieben von: Stephan Williams
  • Kommentare: 13
Samsung Galaxy Nexus Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

10 - 20 Minuten

Einleitung

Use this guide to replace the motherboard in your Samsung Galaxy Nexus

  1. S1qp1QCFF4v1cuDn

    • You must open the back of the phone to access the battery. To do this use the plastic opening tools or your fingernail and insert it into the divot.

  2. 3hCjMAQMwWMrxVCd
    3hCjMAQMwWMrxVCd
    BfGZmYJoiASIVggS
    KNTUvQ51NxLCqNJy

    • Remove the back cover of the phone by moving the prying tool or your fingernail away from the phone while it is still in the divot.

  3. Yni3LD2UR31LIEp1
    Yni3LD2UR31LIEp1
    KF3ybGcwy3ie1mhB
    2TWt3yoFPLuHD2J5

    • Insert your finger into the divot of the battery and pull the battery towards yourself to remove.

    • This is when a new battery will be inserted.

  4. liv1LVfPoHKbhYf1
    liv1LVfPoHKbhYf1
    Tl6ZdXtjk6PWQbFb
    jHlfdvR5YKEfKYqV

    • Remove 4.4 mm screws using a PH # 000 as indicated on the picture.

    The screws need to be labeled with the head type and the length.

    Spencer -

    Confusing heading.

    Dan Brown -

    This is something that cannot be fixed. Due to it being a prerequisite guide it comes up with the title of the guide itself as it is inserted as a prerequisite guide.

    Stephan Williams -

  5. l4DKxpCiKZKYcJdT
    l4DKxpCiKZKYcJdT
    EactQWxATQByFmwD
    T4vKZM3ttWDjXqRp

    • After removing the screws be sure to turn the phone right side up.

    • Insert your plastic opening tool between the screen and the outer case. Move the opening tool around the phone without removing it from in between the screen and the shell of the phone.

    • Pop the screen out of the outer shell. Be cautious not to damage the control board or the screen.

  6. mEgaaYxyKCGIaM1q
    mEgaaYxyKCGIaM1q
    HfnRd5gF4OSw6Ij1

    • Unscrew 4.4mm with a PH #000 marked screw.

    Add head type for screw.

    Dan Brown -

  7. ZUaXx4TSTms5GQcr
    ZUaXx4TSTms5GQcr
    l3SHyNFK6NAl6wDo

    • With the flat head screw driver pull up the blue connector.

    flat-head? flat head?

    Dan Brown -

    Great pictures!

    Dan Brown -

    Don't omit articles.

    Dan Brown -

  8. PERUAWJFKSlQuWYu
    PERUAWJFKSlQuWYu
    AgUYDDsZ21M1JuVA
    TPI6ZVPdIKK3DbMS

    • With you finger or prying tool pull back bottom module.

    You should add a step to pry off the connection on the side of the board also.

    Spencer -

    Change "pulled back" to "pull back."

    Dan Brown -

  9. lZyHxfWTWfHMQ1yf
    lZyHxfWTWfHMQ1yf
    SEDqvXLL3jYJErAL
    FawLwHN1K5XnLp55

    • Remove the internal battery using tweezers or your flat head screw driver.

    • There is glue at the bottom keeping battery and chassis stuck together.

  10. USEkuHUVh3pdCmqq
    USEkuHUVh3pdCmqq
    2QroRFdpjhonBHHw

    • Peel the display connector strip off the main circuit board using the tweezers.

    • Peel the USB connector strip off the main circuit board using the tweezers.

    There are 2 tabs that need to be disconnected, not just one.

    Spencer -

  11. jC3Z2pF4r6unDk5J
    jC3Z2pF4r6unDk5J
    o1u6oBqyy6v1Gjqu
    tJPhqxAqQrlKubDR

    • Remove the antenna using either your fingers or tweezers.

  12. xtuLpkapw4jBGkJZ
    xtuLpkapw4jBGkJZ
    tSxaSS1ABseegPl3
    iVFuZLcSO6VCbsGr

    • Using tweezers, pull the top circuit board off.

    • Depending on your model, there may be ribbon cable connectors attached to the underside of the board. Be careful not to rip them out of the sockets when removing the board.

    Last photo is blurry.

    Dan Brown -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Stephan Williams

Mitglied seit: 22/09/14

1474 Reputation

2 Kommentare

I believe the blue tool needs to be called the "plastic opening tool."

Dan Brown -

were i can find mother board i need the mother board

bangera.kaushik990 -