Samsung Galaxy On5 Speaker Replacement

Geschrieben von: The Dark Night part 2
  • Kommentare: 2
Samsung Galaxy On5 Speaker Replacement

Schwierigkeitsgrad

Moderate

Schritte

9

Zeitaufwand

20 - 35 Minuten

Einleitung

The Samsung Galaxy On5 speaker is located in the back of the phone. Now getting to isn't difficult to get to, but once you're in the phone chaise everything is smooth sailing.

  1. BINt3QToqOBuqZXB

    • Locate the side notch that allows you to open the back casing.

  2. aO3vfLZpUoFNuRZl
    aO3vfLZpUoFNuRZl
    KYZ2MoFBF11Buodi
    uE1tkssx1viUZDJQ

    • Use a plastic prying tool or your fingernail to pop the back cover off of the phone.

  3. CDPvelw6mORCNEFa
    CDPvelw6mORCNEFa
    qrxmMh1BpnpyXRUi
    RoRQEABbZYNr6b1p

    • Locate the battery notch and remove the battery, using either your finger or a plastic prying tool.

    • Be careful not to puncture the battery. Lithium-ion batteries are highly flammable when exposed to oxygen.

  4. XDeLfW6NNTtpHKPO
    XDeLfW6NNTtpHKPO
    hqXOpejY6wAVerob

    • Before disassembling the phone, take out the SIM card and microSD card.

    • Use a plastic pry tool to slide both of the cards out.

    • Do not use a metal pry tool. Using this could cause damage to the cards and/or card holder.

  5. VepQnweSQYdYiHte
    VepQnweSQYdYiHte
    q4AXv6LkEUrBIMGN
    1MUUwnUTHAUkUDHJ

    • Use the plastic Spudger tool to pry open the LCD ribbon cable cover.

    • This part might be a little hard to open. Take your time and be careful not to push too hard as doing so could result in damage to the ribbon.

  6. T6QmTSGMCCXW2GAV
    T6QmTSGMCCXW2GAV
    lWClcuKlOSPPeVy4
    DsZ2qAimD5cWOftK

    • Using a plastic pry tool, carefully pry the LCD ribbon cable from the logic board.

    • Do not use a metal pry tool. Metal pry tools can cause damage to the logic board and to the ribbon cable.

    • This LCD ribbon cable sends signal from the logic board to the LCD screen.

    Not strictly necessary, unless one is removing the display.

    Andrius Tamulis -

  7. l6Baumgt2rDgfsOO
    l6Baumgt2rDgfsOO
    W2nf21tWMKZaRhYq

    • Take a Phillips #00 head and remove all 9 screws. Once done place them aside where you won't lose them.

    • All 9 screws are the same size.

  8. nWdQDjbWkG6xGle3
    nWdQDjbWkG6xGle3
    hZ44LkOsoXLHA6FP

    • Use an iFixit plastic pick to pry away the LCD from the back assembly.

    • This process will take some time due to the glue that's holding the LCD and back assembly together. Slowly move around the edge of the screen to loosen the glue up.

    • If you have a heat gun, you can use it to heat up the glue. Heating up the glue makes it easier to separate the LCD and back assembly.

    Takes some time, and prying away the top of the phone - where the battery isn’t - is tricky. One can easily start unintentionally prying the display from the assembly.

    Andrius Tamulis -

  9. yrLHKZOAFMoOXFEX
    yrLHKZOAFMoOXFEX
    CrXfYJGrpDDepdiE
    HYDbirIcEbJMSXfK

    • Once both the LCD and back assembly come apart, look at the back assembly where the speaker is located.

    • Once located, take the plastic pry tool to remove the speaker from its housing and replace it with a new one.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

The Dark Night part 2

Mitglied seit: 19/09/18

962 Reputation

0 Kommentare