Samsung Galaxy Tab 10.1 4G Charge Port Replacement

Geschrieben von: Ashley Stark
  • Kommentare: 3
Samsung Galaxy Tab 10.1 4G Charge Port Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

10 Minuten

Einleitung

There are a few important things to recognize when replacing the charge port. The connection between ribbon cable and motherboard is initially tricky, but when you've loosened the connection, the ribbon cable will slide right out. There is some adhesive between the ribbon cable and the device near the charge port. It's okay to pull this loose because your new charge port will have more adhesive.

  1. UyfJFalhKEKWSsgd

    • Power off your tablet before you begin disassembly.

    • Screen side facing you, rotate device 180 degrees so the "SAMSUNG" logo is upside down.

    Je pense qu'il y a un problème sur ce tuto, quand on démonte la vitre avant, le LCD reste sur la tablette.

    Antonio Jimenez -

    Surtout ne faites pas comme indiqué sur les photos, il faut décoller la plaque grise au niveau de l'appareil photo, déclipser le tour de la face arrière, et dévisser les trois vis du haut côté caméra.

    Antonio Jimenez -

  2. J1fQXAeXIYEPArMC
    J1fQXAeXIYEPArMC
    lZ66UlIEXKWONvwk

    • Using the plastic opening tool, start in the center near the charge port and wedge the angled tip between the plastic back and the glass screen.

    • Create a wedge and apply pressure. Use the tool to separate the screen from the back until you hear an audible “pop."

    • Continue to wedge the tool about every inch along the current edge.

  3. GAlwSWxIxSL42RKE
    GAlwSWxIxSL42RKE
    AHEklNM4GvIi2lYj

    • Once the bottom edge has been loosened, work towards a bottom corner from the other edge and continue to wedge gently until you can “pop” the corner out.

    • Continue this process on the other bottom corner until it can be popped out as well.

  4. 6cu1lPOhk2Dk14hG

    • Place your hand between the device and the back panel. Then continue the wedging motion along the top edge of the device until the back panel comes loose.

    • Do not wedge the tool directly on top of the power buttons and headphone jack. Wedge nearby so that you don’t damage internal hardware.

    Bonjour, je pense qu'il y a un problème sur ce tuto car quand on enlève la vitre avant, le LCD reste sur la tablette.

    Alors que normalement il faut démonter la plaque arrière, les images sont fausses.

    Antonio Jimenez -

  5. whcQyCHpkFUC4vOL

    • Remove the back from the device.

    • Excessive force shouldn't be necessary here. If the back panel is sticking, find the area of the edge closest to the sticking point and wedge the opening tool there until the back panel pops free.

  6. mHRkhj32sTUp6gRX
    mHRkhj32sTUp6gRX
    uA61bDmBEjlfoqjM

    • When working with electronics, it's important to choose a tool that's ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.

    • The connection between the battery and motherboard is a group of four wires in black housing that can be found near the top middle of the device. Using a plastic spudger or a flat, slim tool, lift the black connector housing upwards to disconnect it.

  7. ByTROjBGcniLhchV
    ByTROjBGcniLhchV
    aFQmcv4JaoibtDTB

    • Remove the tape covering the charge port ribbon cable.

    • Keeping the tape is not necessary.

  8. DAsiBLATvVcBHy2b
    DAsiBLATvVcBHy2b
    If6PTnrDP2iYtWev
    ja4Myb66DYEEPTRD

    • Slide a plastic spudger tool under the strip of black plastic on the back of the ribbon connector.

    • Metal spudgers can puncture an unprotected battery, potentially causing a fire. When working with electronics, it's important to choose a tool that's ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.

    • Gently lift with the spudger to flip the connector up. This will release the ribbon from its connection.

    • Slide the ribbon out of the connector.

  9. 3DhWpoEYWs5bcMEB
    3DhWpoEYWs5bcMEB
    cOIrtXPYJPPh3NvO

    • Use the Phillips #00 screwdriver to remove both of the 3-mm screws.

  10. 3Pu1CArB2jjUUwK1
    3Pu1CArB2jjUUwK1
    uhrmYY2CleGRaYae
    TEWONBHbM6XWeymj

    • Slide the plastic spudger under the charge port to lift it from it's housing.

    • Pull up on the charge port to remove it and its ribbon cable.

    • You may have to pull fairly hard; the adhesive holds the bottom section of cable to the tablet tightly.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Ashley Stark

Mitglied seit: 23/09/15

1202 Reputation

0 Kommentare