Samsung Galaxy Watch3 Display Replacement

Geschrieben von: Tobias Isakeit
  • Kommentare: 1
Samsung Galaxy Watch3 Display Replacement

Schwierigkeitsgrad

Moderate

Schritte

8

Zeitaufwand

20 - 45 Minuten

Einleitung

Use this guide to replace a cracked or broken screen on your Samsung Galaxy Watch3.

  1. a63LjGHbMHP6JGH2

    • Before starting repairs, take your watch off the charger and power it down.

    • Use a Tri-point Y00 driver to unfasten the four screws on the back of the watch.

    • Don’t worry about removing the screws, they will stay in place in the back cover.

  2. AYFpCm45IBcsXE1V
    AYFpCm45IBcsXE1V
    iwckjD1whPf3Q5wO

    • Insert an opening tool between the back cover and the metal housing.

    • Twist the opening tool to create a wider gap.

    • Don't fully remove the back cover just yet. The sensor flex cable is still connected to the motherboard.

  3. dHpTdiX6DQSZMSxm
    dHpTdiX6DQSZMSxm
    hYr6SZILNpmEg5Tp
    kouxAHaTH1IZYyUV

    • Lay the watch face down.

    • Carefully lift the back cover up from the edge with the buttons to access the sensor connector.

    • Use the flat end of a spudger to pry up and disconnect the sensor flex cable from the motherboard.

  4. E2pyOpJJBim22SJB
    E2pyOpJJBim22SJB
    pREbiCwhYedi16f1

    • Remove the back cover.

    • Make sure the rubber gasket (marked red) is undamaged. If damaged replace it with a new one during reassembly to maintain proper water resistance.

  5. aimUFrHaIQ4NiO6w
    aimUFrHaIQ4NiO6w
    kvmU4aNwkXVxEoJG

    • Use the flat end of a spudger to pry up and disconnect the display flex cable from the motherboard.

  6. QQr4SKMOSMROIhMp
    QQr4SKMOSMROIhMp
    bLEbmDNsXEHpQRNO

    • The core's plastic frame fits tightly within the watch's metal housing.

    • Place the corner of the flat end of a spudger in the small opening of the barometric sensor, on the opposite side of the display connector.

    • Twist and tilt the spudger to lever the core assembly out of the metal housing.

  7. KEsLtgtLXH1hkOml
    KEsLtgtLXH1hkOml
    1oYfcqD3iQ6nYJTC
    VkXxdpnUm3jxqGgT

    • Carefully thread the display flex cable through the gap on the core's plastic frame.

    • Remove the core assembly.

  8. MuEI3YiFpHtgoalo
    MuEI3YiFpHtgoalo
    BVfXEgmFFngQuKiE

    • If your display is cracked, keep glass shards contained by applying a strip of tape over the glass."

    • Use your finger to steadily push the display down through the watch's metal housing to loosen the adhesive.

    • Lightly heating the display with a hair dryer or iOpener can help soften the adhesive.

    • Remove the display.

Abschluss

If possible, turn on your device and test your repair before reassembly.

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Take your e-waste to an R2 or e-Stewards certified recycler.

Tinte & Feder

Tobias Isakeit

Mitglied seit: 31/03/14

108055 Reputation

Ein Kommentar

Any idea how to remove the rotating bezel?

Azhar Suhaimi -