Samsung POWERbot R7070 Vacuum Motor Replacement

Geschrieben von: Eric Anderson
  • Kommentare: 7
Samsung POWERbot R7070 Vacuum Motor Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

8 - 15 Minuten

Einleitung

Replace the motor to mobilize and restore suction power to your POWERbot. The motor will need to be removed to access the Right Driving Wheel.

  1. Jey3JUgsKTqUQDA2

    • Turn the emergency switch off.

  2. fnJATdcpgHeIjLYs
    fnJATdcpgHeIjLYs
    KuX2SroW5S5m5P13

    • Remove the two exposed screws on the top right of the device.

  3. LoqZFmAbFTpVVNAb

    • Lift the cover plate to expose the battery.

  4. mAORAQmChOWaqUgO
    mAORAQmChOWaqUgO
    dXJtaOXPX5QEau6d

    • Using one hand, pinch the white plastic connector where the battery's wiring connects the POWERbot. Pull up to disconnect.

  5. EHiXDicFlGFbYjmw
    EHiXDicFlGFbYjmw
    UCyaThQKipIgotPB

    • Lift the battery from the right side, up and out of its compartment.

  6. KIVmSKb2DjDGueU4
    KIVmSKb2DjDGueU4
    YTN6yqWkgKcil5ny

    • Unscrew the two silver 1.5 cm screws on the left and right side of the battery compartment.

    • Remove the two 1.5 cm screws above the yellow sliding lock tabs.

    • Remove the two 1.2 cm screws in the brush compartment.

  7. yW5UwAWr4pESwram
    yW5UwAWr4pESwram
    iHjRSHNnZLbXbCkq

    • With moderate force, separate the silver top from the black bottom of the vacuum.

    • The cover will only separate a few inches as the two halves are connected by wires.

  8. i1nZBYhSGLNxlTJk

    • Disconnect the white and red wired connector attached to the top half of the base of the vacuum by squeezing the connector and pulling up.

  9. Y4aXE5pOvKcRbxe3

    • Pinching the top and bottom of the black wired connector, pull outward, fully detaching the top from the bottom of the device.

    how do you pinch the top and the bottom when the bottom seems to be glued to the motherboard?

    Royal Coach -

  10. ikjl6IVKZkqiOgNV

    • Detach the wide circuit connector on the left side by pinching and pressing down on the right and left side of the clip, pulling the connector out.

    • Pull the connector out by the left and right side of the white clip and not by the wires.

  11. fPCG2BuoOWmLOcSi
    fPCG2BuoOWmLOcSi
    4AOKElT2Eaa4knNy

    • Remove the four 1.2 cm screws.

    • Remove the single 0.8 cm screw.

  12. ZmjEsXvg5EYLHxsf

    • Remove the two 1.5 cm screws on the motor chamber.

  13. quDk2gUQqqTibvMW
    quDk2gUQqqTibvMW
    CC6poJhB6kBUvZld

    • Lift the motor by grabbing the body of the motor, lifting upward.

    • With the screws removed from the motor chamber the top of the motor chamber will pop open.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Eric Anderson

Mitglied seit: 11/09/17

465 Reputation

6 Kommentare

Anybody know where I can get the motor?

donstatus87 -

I'm getting a Power brush error. Does the motor contain the power brush square socket and gearing?

Steve.

Steven Nicholas -

One can actually open up the motor housing and take out the metal motor. Be careful not to break the clips when opening the housing… because I did…. but duct tape will prolly hold it together again. Anyway , the motor bears the following markings in my R7040: VCM-140CLDA DC21.6V 145W 2018.5.22-12.50

Have fun!

websites140 -

Easy to replace and found a refurbished motor on eBay.

David Trinkle -

Thanks for this guide! My motor was making a high pitched whine and grind - bought a replacement refurb motor on eBay for $39; hope it works.

joey -

Hi. I have a very important question. vr7040 also has 10w motor, can i replace this motor with other vr7065 vr7070 engine? Is there a problem with the electronic circuit?

Hulusi Şen -