Samsung Radiant 360 R1 Speaker Replacement

Geschrieben von: Angelo Espinosa
  • Kommentare: 2
Samsung Radiant 360 R1 Speaker Replacement

Schwierigkeitsgrad

Moderate

Schritte

9

Zeitaufwand

20 Minuten

Einleitung

A tweeter speaker its the speaker that drives the highest range of frequency in the speaker. This guide will serve as a reference to replace the speaker/tweeter in the Samsung Radiant 360 R1 in the case that it becomes damaged.

  1. qFj6A6DOJjkmwn4g

    • Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

    • Use the plastic opening tool to lift and remove the rubber grommet plugs.

  2. pJ21wxngg13RTVPU

    • Using a PH1 Philips screwdriver, remove four (9.5mm x 1.6mm) screws from the base plate.

    • Remove base plate by stabilizing speaker and using plastic prying tool to pry the base plate from the speaker.

  3. Zbs1l32MBXQsce4v

    • Place the speaker on the table with the Touch Pad facing down. This will leave you with the Port Panel exposed.

    • Remove speaker grill by stabilizing speaker on a table and applying pressure to the bottom of the speaker. Slide the speaker grill up and away from the remaining endcap.

  4. mb5SXhoEUDmuW2qO

    • Remove the two exposed (9.5mm x 1.6mm) PH1 Phillips screws on the Port Panel.

    • Remove the Port Panel from the speaker body, exposing the ribbon cables.

  5. TDdcMom4Duo5aTAE

    • While stabilizing the Port Panel remove the two ribbon cables one at a time by pressing the locking clip down on the ribbon cable connectors and pulling the connector away from the Port Panel.

    I understand this is a guide for working on the Samsung wam 1500 yourself. But where can you get the parts from. I can not find them online. I need to replace the usb/power port panel

    Brian Vickers -

  6. OfNRnIwqrxTIamBg
    OfNRnIwqrxTIamBg
    j6sx4MU1QdHqB1Vs
    NYLtqPYOsgK3RaCe

    • Remove the four (9.5mm x 1.6mm) PH1 Phillips screws on the port speaker body.

    • Remove the Port Panel exposing the subwoofer.

  7. FDVkLv4f6NHamQZo
    FDVkLv4f6NHamQZo
    FDYKClpCfaWQR1QK
    NjiqehJNBjQI6sao

    • Remove the eight (9.5mm x 1.6mm) PH1 Phillips screws on the right side of the speaker body.

    • Remove the one (9.5mm x 1.6mm) PH1 Phillips screw on the left side of the speaker body.

    • The body sides are denoted with a "R" and an "L" for right and left sides.

  8. 5HGjoLHovcoaZ4Eo

    • Open up the body to expose the inner panel and motherboard.

  9. C1DJUMybxBCCwgVV
    C1DJUMybxBCCwgVV
    yqNJJbCpPNuknafI
    m3JlOBBYIms2bxxk

    • Remove the ribbon cable from the tweeter which is attached to the main motherboard.

    • Slide the tweeter out of the enclosure.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Angelo Espinosa

Mitglied seit: 02/02/17

116 Reputation

Ein Kommentar

Although not 100% complete, the disassembly process is exactly the same for the R3 & R5 as well as the pictured R1.

Matt -