Samsung WB150F Lens Assembly Replacement

Geschrieben von: Wyatt Turner
  • Kommentare: 2
Samsung WB150F Lens Assembly Replacement

Schwierigkeitsgrad

Moderate

Schritte

11

Zeitaufwand

20 Minuten

Einleitung

This guide provides a walkthrough on replacing the Samsung WB150F lens assembly if your device has poor focus or uneven focus across an image.

A camera lens is a tool used to bring light to a fixed focal point.

Before using this guide, inspect the battery to ensure that the device is receiving power.

Prior to beginning, make sure to remove the battery from your camera and disconnect from any external power source.

  1. smupvQqyT1qVUpVG

    • The location of the battery compartment can be found on the underside of the camera.

  2. jUCrbtxbMXYZDt36
    jUCrbtxbMXYZDt36
    5HkEZbHSFL5AHlon

    • Have the lens of the camera face you. To open the battery compartment, slide the battery door lock towards the left. At the same time allow the battery door to swing open.

  3. TIJmkWPNGBYFF2Zk

    • Gather a PHO Phillips head screwdriver and a plastic wedge. If you do not have a plastic wedge like the one pictured, a credit card or a guitar pick can be used.

  4. ZD5WsfduUiReslhq
    ZD5WsfduUiReslhq
    DoQfwuvhNQI2mBKV
    6wWQ6JWeKGSB34Pn

    • Take off the front casing by using your screwdriver to unscrew the screws circled in each of the photos (5 total).

    • The front casing can now be pulled from the camera.

  5. MjiEmNR5wZRUrXUj

    • Your camera should now look like the camera in the photo.

  6. CxMfyc5ZADQHXX1m
    CxMfyc5ZADQHXX1m
    JHYQrxEmOIOwOR4o

    • Flip the camera over and pry the back shell of the camera off with the plastic opening tool (or credit card or guitar pick). The screen-side of your camera should now resemble the camera in the second photo.

    • Note: removing the back shell does not require removing anymore screws, it should just snap off.

  7. 4j56pVeaFQpAMhaS
    4j56pVeaFQpAMhaS
    wh4KPSa3cYHXOYrr
    urGIFaBKHvUNRJBk

    • On the screen side, remove the button circuit board (outlined in red) from the camera by using the plug located in the upper right corner of the screen side.

  8. FMICiomj1xXQ1NYX
    FMICiomj1xXQ1NYX
    TBeCZEs2XOXUZYMG
    k3TvfWCr1blZisFE

    • Remove the metal casing by lifting up the old screen and unscrewing the 5 screws circled in the first photo.

    • The LCD screen has a ribbon going to the main circuit board, as shown in the second photo, that needs to be detached.

    • Your camera should now resemble the third photo.

    There is no need to remove the metal shield as you can get to the connector for the ribbon cable without removing it. Saves you a lot of time.

    Braxton -

    yes,just like Braxton's saying

    luguo52020 -

  9. NjwiSd4wUEMCunZW
    NjwiSd4wUEMCunZW
    WQJQCoToZ4FPSkmF
    yGAbrZJPJOnmkusy

    • Disconnect the ribbon from the flash assembly.

    • Disconnect two ribbons from the lens assembly as shown in the second picture.

    • Disconnect the ground wire from the motherboard as shown in the third picture.

  10. DOKkux3XAtFSm1kf
    DOKkux3XAtFSm1kf
    bgkK6Ep361LCVilR

    • Remove the motherboard from the camera housing.

  11. bVyND2XQUAnBDOOF

    • Lens assembly freely detaches from housing once both ribbons are detached from the motherboard.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Wyatt Turner

Mitglied seit: 12/04/22

265 Reputation

0 Kommentare