Scanner Head Replacement

Geschrieben von: Mackenzie Billings
  • Kommentare: 8
Scanner Head Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

Keine Schätzung

Einleitung

This guide will show you how to access and replace the scanner head on your HP PSC 2410 Photosmart All In One Printer.

  1. haINTTumYxp3mYOC

    • Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

  2. Ap5Uy5oAk2FDN1d3
    Ap5Uy5oAk2FDN1d3
    SlR2aJmhOCJIVBen

    • Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

  3. uRLL5YRQKwYBuYxZ
    uRLL5YRQKwYBuYxZ
    qPYpTYJ35SpWkGjP

    • Press down on the two plastic hinges to remove the upper portion of printer.

    The two plastic hinges WON’T PRESS DOWN in order to release them from their housing and lift away the top. I am even resorting to wedging a very thin flat headed screwdriver in on top of the hinge to see if this makes a difference but nothing will budge.

    Maeshowie -

    Further to my first comment, the hinge in the diagram looks slightly different to the ones on the rear of my printer in that the diagram ones look as if they WILL press down, finger force, to release the top.

    I’ve given up and am putting it all back together again. Must now look to see if I can send this printer to someone who knows what they are doing.

    Maeshowie -

    Third and last comment. I tried one last time to release the top, pressed down on the hinge - and it snapped off. This one to the dump and online to buy a new one.

    Maeshowie -

  4. HeuJd2UUBK6WjtTq

    • Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

  5. JY4Ae6APHYFqZvSk
    JY4Ae6APHYFqZvSk
    OKHqoy3OErmwIUk3

    • Rotate the printer so the paper tray is facing towards you.

    • Gently lift the scanner tray up and away from the printer.

    • Press the gray plastic tabs inward to release the tabs from the printer.

  6. RcxXfsgrFhXmjC2g

    • Returning to the back of the printer, remove the scanner from the back hinges.

    • With pressure applied, the scanner will detach easily.

    It would be easer to do steps 7 & 8 before step 6.

    Richard Scott -

  7. 1DOPi3dgFHLqMgNm

    • Gently grasp and unplug the two white ribbon cables from the printer body.

    • Be sure to grasp the cable at the connector and not to pull on the wires themselves.

  8. FEH1t4XJPfvRkWUU

    • Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it's port.

    • Be sure to grasp the white connector and not to pull on the wires themselves.

  9. 5VXsMWwSxUy1wCJp

    • Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

    But how do you get to the inside of scaner?

    R S V P Urgent

    Paul D

    pauldaley08 -

    As from N0 9 Done thus far but can not get inside scanner itself. Have removed screw Back L H Side, but do not wish to brake in — somthing is holding (more screws?)

    Yrs Paul D

    pauldaley08@hotmail.com

    pauldaley08 -

  10. 4DZuuSDJDLYrOrYP
    4DZuuSDJDLYrOrYP
    KopirUs1XeaPeesW

    • Detach the white ribbon wire from the scanner head by pulling gently at the connection.

  11. 3qYyaftZaniOV1K3
    3qYyaftZaniOV1K3
    YZ121UcBpfC2bYAm

    • Lift the gray drive belt from the black tab to disconnect the drive belt from the scanner head.

    • Remove the scanner head from the scanner by gently rotating and then lifting.

  12. vGVGjVSK24f6Vftl
    vGVGjVSK24f6Vftl
    tCGc1OcAACgqwwro

    • Place the new scanner head in the scanner tray by fastening the drive belt into the black tab.

    • Make sure the tab on the outer portion of the gray drive belt is fastened.

    • Once the drive belt is secured, rotate the scanner head back into position.

    • Re-attach the white ribbon wire to the connection from Step 10.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Mackenzie Billings

Mitglied seit: 05/04/11

541 Reputation

2 Kommentare

Ok, but where do I purchase a new scanner head???

Nichelle King -

the step between 9 and 10 doesn't seem to make sense. it never established that the scanner head is broken...I couldn't identify where step 10 scanner head came up ...no where did it show the scanner between step 1 and step 9...Please offer an explanation...

by step 9 the scanner package had already removed...i m afraid I wont here from ifixit because the printer is about 20 years old.

winston ho -