SodaStream Source Demontage der inneren Bauteile

Geschrieben von: Angela Mossgrove

Kommentare: 32

SodaStream Source Demontage der inneren Bauteile

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

30 - 40 Minuten

Einleitung

Werkzeuge

Schritt 1

Schiebe die Messingstange, die sich am oberen Ende des Geräts befindet, heraus aus dem "Sprudel-Block".
Du kannst die Spitze eines Schraubendrehers benutzen, um das Teil auszudrücken.

We could,remove this covee, without sliding the assembly out ofbthe case. There was NO gold bar in the system…

Robert Coles - 01/07/20

….. no gold bar either in my device…. ??????

hbergeron - 30/12/20

Schritt 2

Schiebe die gelbe Akku-Abdeckung nach oben, um sie vom Gerät zu entfernen.

Careful! I had springs and retainers go flying on this step

Felicia Renaud - 31/08/20

Yep…same here. Took me a good minute to figure out where they came from!?

Rodney Davis - 27/03/21

Fun fact: The lights on the SodaStream are simply a timer. They are in no way linked to a pressure gauge. If you want more bubbles it doesn't mean you have to press on the activation mechanism harder. you can press gently and just wait longer. This way the water will not spill out over the top and leak all over the table. Ignore the lights and just wait for the safety release valve to activate as you are filling the bottle. that's how you know you have reached the limit.

Ken Ostrovsky -

Schritt 3

Hake das untere Ende des Plastikarms auf beiden Seiten des Gerätes aus.

Schritt 4

Hebe das obere Ende des Plastikhebels mit einem Spudger an und entferne das Bauteil auf beiden Seiten.

Slot screwdriver works just fine for these next two steps

Scott - 14/02/21

Schritt 5

Entferne das Plastikstück, das sich ziemlich weit vorne auf dem "Sprudel-Block" befindet, mit einem Plastiköffnungswerkzeug oder einem Nylon-Spudger.

Be careful…they will fly off across the room!

Rodney Davis - 27/03/21

Schritt 6

Entferne das Plastik-Oval und die Feder darin.

Do not have this piece on mine?

ronkellington - 11/12/20

nor do I. They must have made some changes.

Scott - 14/02/21

This piece exists on my 2013 metal chassis version, but not on my 2016/17 plastic chassis.

Darryl Marko -

Schritt 7

Ziehe die Abdeckung der Flaschenaufnahme nach unten und weg vom Sprudler-Block.

Schritt 8

Entferne die drei 17,9 mm Schrauben auf der rechten Seite.
Es kann schwer sein, an diese Schrauben heranzukommen.

Should this be four screws? I followed all directions (I think) and had one extra screw to remove, just above the bottle mount, before I could split the two halves apart

Phil Wilkes - 02/06/20

Yes I had a 4th screw at this step too. Going backwards the missing fourth screw in the instruction messed me up and I had to redo it!

Daniel Sylvester - 28/07/20

Yes the 4th screw still isn't mentioned - and just below it is the rare-earth magnet that can fall out when the halves are separated. This magnet activates the LEDs when the carbonating block is pushed down - no magnet, no lights.

Malcolm Noble -

Schritt 9

Löse die vier Clips oben am Sprudlerblock und entferne die Plastikabdeckung.

Schritt 10

Hebe die Clips, die sich auf beiden Seiten befinden mit einem Plastik-Spukger an. Entferne die vordere Abdeckung .

Schritt 11

Löse die Federarme auf beiden Seiten des Gerätes, indem du sie nach unten drückst.

Schritt 12

Ziehe die rechte und linke Seite des Geräts und trenne sie in zwei identische Hälften.
Wenn du diese zwei Teile getrennt hast, fallen alle übrigen internen Komponenten aus dem Gerät.

what happens to the middle white piece?

Noah Langer - 25/04/20

Yeah there's a step missing here…between 17 & 18

Daniel Sylvester - 27/07/20

Is it better to lay it on its side?

Gareth White - 05/11/20

I hope someone will document the missing step of what it looks like if you separate the halves without having all the parts fall out.

What does it look like and where do they go? Kinda' important for reassembly.

Joe -

I've added a photo to this step showing just this, fingers crossed it gets approved

lizzbeeton -

Liz - would you post a link to your pic here so we can see it even though it's not approved yet?

Joe -

Re: "missing step"

On the newer models, (at least 2016/17) the valve is attached to the left side and it's two Phillips head screws must be removed.

These instructions are correct for earlier models where the valve is in the middle, so there is no missing step.

Darryl Marko -

Se voce deitar o aparelho com cuidado, nada cairá e as peças ficarão no lugar

J.Poppa -

Thanks to this guide, I’ve taken a part my SodaStream Source a few times now. Like others have mentioned, during reassembly, this step tripped me up every time. It’s definitely missing details about the part orientation. I took some additional photos in efforts to help others. Please find the album here.

Mitch -

Thanks Mitch!! That's exactly what I needed! been pulling my hair out trying to figure out how that white piece went back in.

KayLynn Mathews -

You’re very welcome! I’m so glad it helped you out!

Mitch -

Schritt 13

Ziehe die Schaumstoff-Abdeckung nach oben und entferne sie von der Vorderseite des Sprudel-Elements.

Any source for spare parts known? Ebay and Amazon does not help here!

lutz Ziffer - 07/02/21

no foam pad on mine either

Scott - 14/02/21

What is the name of the part that is in blue? Mine is broken and I would like to replace it

Tony R - 12/04/21

The part on mine that was broken is the plastic cap/nut that connects the black hose to the canister holder.

Going to try and superglue it. Wonder if there's a source for this nut?

Joe -

I wish it was that simple. The hose has a brass ferrule crimped on it, and the nut cannot be replaced without being able to remove and crimp a new ferrule to the (new?) hose. I have found a listing (eBay Europe?) for a split brass nut that allows replacement, but...

https://www.google.com/url?sa=t&source=w...

https://picclick.co.uk/Messing-Mutter-f%...

Darryl Marko -