Sony CCD-TR81 Outer Case Replacement

Geschrieben von: Kevin
  • Kommentare: 0
Sony CCD-TR81 Outer Case Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

30 Minuten

Einleitung

If buttons get stuck or you need to make any other type of replacement to the hardware of the video camera, you must first remove the outer case. This guide shows how all of the outer casing is removed, which involves removing extensive amounts of screws. To complete the case disassembly, the audio inputs are also removed from the video camera.

  1. OwGU33mVsCDSVhWg

    • Lift viewfinder to access battery pack.

  2. CisYmC2vvsnOmLr3
    CisYmC2vvsnOmLr3
    Uod45FiEQRVFqpWn

    • Press the battery release button.

    • While pushing the battery button, slide the battery to the left.

  3. PG22ysPsowD3OFr2

    • Pull the battery pack out of the video camera.

  4. Xdsn6YIbCLMYmdDV
    Xdsn6YIbCLMYmdDV
    2E6NMhA6B2ZFVqSu
    EHsQQyAiUXvlf1k6

    • Open the cassette cover.

    • Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm.

  5. CTVpqLNDQBXvla1Y
    CTVpqLNDQBXvla1Y
    qLUNnrFYGHPnXOde

    • Remove five screws from the right side, from bottom to top, 3x4.54mm 2x5.70mm.

    • Remove the single 4.5 mm screw from the backside.

  6. QAXuQLTr1L1HoUHf

    • Pull off the plastic tape cover by lifting it up and out of the camera base.

  7. p1fxLu6mrxIkWFZL

    • Disconnect the mic assembly by pulling it away from the camera base.

    • Do not pull too hard as the wires are still connected.

  8. xVM4HvNAHaKOtglc

    • Pull the bottom part of the case away from the camera.

  9. FO5C2LjtMHBv6rR3

    • Remove the three 4.5 mm screws from the right face of the video camera.

  10. 1UN3ZGggaDf5YBV5

    • Remove the single 3.6 mm screw at the front of the video camera on the circuit board.

  11. SXQWA2e3sFwCpkVG

    • Pull the audio/video inputs underneath the microphone assembly. The inputs should still be connected to the circuit board.

  12. LpehTOYBW2vlIFdx

    • Remove two remaining 3.6 mm case screws from the front of the camera.

  13. sFfQCH1K2aLPsWHZ
    sFfQCH1K2aLPsWHZ
    uHi3rYqFUJIRQV4u

    • Using metal tweezers, pull out the plastic connector box on the front side.

    • Again use metal tweezers to pull out the connection box on the bottom of the camera. The right side of the case can now be removed by pulling it to the right.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Kevin

Mitglied seit: 24/01/11

232 Reputation

0 Kommentare