Sony XAV-AX100 Display Replacement

Geschrieben von: Abdulaziz Redha
  • Kommentare: 4
Sony XAV-AX100 Display Replacement

Schwierigkeitsgrad

Moderate

Schritte

9

Zeitaufwand

40 Minuten

Einleitung

By following this repair guide, you will be able to replace the full Head Display; thus, providing yourself with better visuals and imaging.

  1. xsmMKycf52xfUZOH
    xsmMKycf52xfUZOH
    dFGauf4WlttbqBPF
    CUFGa2VZkGe2TW5Q

    • Place the device on a flat surface, upside down, so the bottom of the screen would be facing upwards.

    • Remove the ten 3.5mm Phillips #0 screws from the back plate.

  2. B2GFcRl3GaI5a3Yk
    B2GFcRl3GaI5a3Yk
    bL2CJSZAlKgp4Rxb

    • Use a plastic opening tool to remove the back plate.

    • Don't remove completely as there will still be cables connected.

  3. 5RPDNuHstMwktSKN

    • Disconnect the USB cable from the display board.

  4. qaPKP6hHdmZvxAdK

    • Adjust the rubber holders that are keeping the USB cable still on the motherboard, so you can remove the cable entirely from the inner compartment.

    • The rubber holders are extremely sensitive to any applied force. Therefore, be careful while turning them around.

  5. r4JkgkMCpNMhhKS2
    r4JkgkMCpNMhhKS2
    AdvJpMRSHQSQhURQ
    ZrPvVqJlJM5wgwC1

    • Remove the 3.5mm Phillip #0 screw that secures the USB cable to the back panel.

    • Pull the USB cable off of the back plate.

    Our radio is not interfacing with my phone it says USB connection problem before I tear it all apart what else could it be thank you

    Don Bartolotta -

  6. uYsOJ5qGYQqGHBKh
    uYsOJ5qGYQqGHBKh
    GCsQFgZJuEUlY1fL

    • Disconnect the display power cable from the motherboard.

    • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

  7. XxvsfqcPdKU1OPdB
    XxvsfqcPdKU1OPdB
    ad2LxjmRScpmXQdu
    UFTNKRsnOogdDDLm

    • Unscrew the four 3.5mm Phillips #0 screws from the motherboard.

    • Use a spudger to gently lift the motherboard up and out of the radio.

  8. tYYtqC1iPJCqNisg

    • Remove the four 3.5mm Phillips #0 screws from the sides of the display.

  9. TZUW1KsCpDn3A6Z2
    TZUW1KsCpDn3A6Z2
    YZXaLC6Bma3PC3lY

    • Remove two 3.5mm Phillips #0 screws from the back of the head unit.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Abdulaziz Redha

Mitglied seit: 23/02/18

741 Reputation

3 Kommentare

Where do you get a replacement screen?

I need one for a xav 3005 db

Morten Hjorth-Johansen -

Thank you very much for this great write up.

However after having performed it, if all you are doing is replacing the screen, then steps 1, 4, 5 and 7 are actually completely unnecessary . There is no need to remove the back panel or the motherboard.

but thank you nonetheless for having shown the way.

Robert Edwards -

I need to get a replacement screen for a Sony xav 1500 any idea of a cheap place?

Abelardo M. -