Sony Xperia XA2 Ultra Charging Port Replacement

Geschrieben von: Alyssa Bayles
  • Kommentare: 0
Sony Xperia XA2 Ultra Charging Port Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

10 - 15 Minuten

Einleitung

If the Sony Xperia XA2 Ultra is not showing any signs of connecting to a charger to replenish the battery life, then it will need to be replaced.

Before taking any steps to open the phone, make sure that it is turned completely.

Be aware that when using a heat gun (or something similar) that the device will heat up. Continue with caution.

  1. ThfMGLRciTuvQw1T
    ThfMGLRciTuvQw1T
    bcSJNGaVS1MxDqyt

    • Turn off your phone before continuing.

    • Remove the SIM card tray on the left side of the phone using a SIM card eject tool.

  2. SVUVxQroQLfroEQF

    • Heat the edge of the phone with the heat gun (recommended) for 30 seconds.

    • If you don't have a heat gun, a hair dryer can be used.

    • Use the hair dryer on the highest setting, constantly going around the phone to heat all of the edges.

    • The phone will become hot to the touch. Use gloves or a towel to touch the phone.

  3. OemycEx4qEQgNYcZ
    OemycEx4qEQgNYcZ
    QGVhkcCcYeyHrGhX

    • Apply the suction handle near an edge of the phone and pull upwards while trying to get an opening large enough for an iFixit opening pick.

  4. mJBSoioDvsKaSLMe
    mJBSoioDvsKaSLMe
    ns6lmMXqTrvwMkDt

    • Pry upwards with the pick to start pulling the rear cover off the adhesive it’s attached to.

    • Insert a second pick once there is enough room.

  5. wYydXKM1sgRDTlfx
    wYydXKM1sgRDTlfx
    NNg2oZV5LJRsqXmR

    • Take one of the picks and try to slide it down the side of the phone, pulling more of the cover off the adhesive.

    • The iFixit opening tool may also be used to gain better leverage.

    • The rear cover will pop off.

  6. LOi43chLTPsAIRIf

    • Once the rear cover is off, use the iFixit opening tool to detach the flex cable.

  7. Y4wJUMV2GS1Vg5te
    Y4wJUMV2GS1Vg5te
    BiPrVakmIMcmdptB

    • Remove the four 3 mm screws using a Phillips #000 screwdriver.

  8. 5UTRXBDMscZpbDGF
    5UTRXBDMscZpbDGF
    2MBJy5pMDafaPwP5

    • Using an iFixit opening tool, pry and remove the speaker.

  9. kYcFIPwYeBIoRoBw

    • Using the iFixit opening tool, disconnect the flex cable.

  10. 3vtlVlkvgNQ3kk5d
    3vtlVlkvgNQ3kk5d
    bdm6f2NNZAg5hjYx

    • Remove both the black and white antenna cables using the Jimmy.

  11. cPRupLtUrMAqLhrY

    • Remove the vibration flex cable with the Jimmy.

  12. edWZQphZb3eIUAdl

    • Using the Jimmy and the iFixit opening tool, remove the charging port.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alyssa Bayles

Mitglied seit: 27/09/22

819 Reputation

0 Kommentare