Einleitung

This guide is useful if the keypad on the device is broken or faulty.

  1. YsrEcrV5i4RNhRXV
    YsrEcrV5i4RNhRXV
    kEcWLxVrRWjT5k4N
    LjYVTRdlgRW2W3mi
    • To remove the battery cover, first turn the phone so that the keypad is face down.

    • While holding the phone with one hand, place the thumb of the other hand at the top of the battery cover.

    • Slide the battery cover toward the bottom of the phone to remove.

  2. RyZ2DFmiveqIE1k1
    RyZ2DFmiveqIE1k1
    JFPxBlCj4mUgdKbt
    • To remove the battery, first grab it using a finger on either side.

    • Pull the battery upward, while securing the phone with your other hand.

    • Gently remove the battery and place it to the side of the phone.

  3. tqsv1LpthmH1YDdE
    tqsv1LpthmH1YDdE
    Iiny46YfGCUWRhFf
    gMJhUhr1qvR4cNE3
    • Move the battery and battery cover to the side and pick up the phone.

    • Use the plastic opening tool to remove the camera casing located at the top of the phone.

    • Use your fingers to pull out the gray antenna casing.

  4. bHBMktKDQFnAF2Eu
    bHBMktKDQFnAF2Eu
    Q2A4kKsIqD4MEXpV
    4GYjV5FFhvHj3fMK
    • Hold the phone with one hand and the plastic opening tool with the other.

    • Pry the outer casing off of the phone by wedging the plastic opening tool between the casing and the phone, thus dislocating the tabs.

    • Place the outer casing to the side.

  5. ORV5rGNHPs1DAVLH
    ORV5rGNHPs1DAVLH
    paoD1wjB6SUqQTJu
    WabBEGmxknCDKXZp
    • Using the T5 or T6 screwdriver, remove the six screws from the back of the phone, as shown in the first image.

    • Remove the back half of the phone by using the plastic opening tool to pry apart the top half from the bottom half. Wedge the plastic opening tool tool around the edge of the phone to dislocate the tabs.

    • Once the tabs are dislocated, pull the back of the phone apart from the front half.

  6. L4QHQZprDNULgJVN
    L4QHQZprDNULgJVN
    JQ5dK6gLCEvTXnTY
    wMDkOShjdTvip2HF
    • On the rear phone casing, locate the ribbon cable tab and connector next to the SIM card port.

    • Gently pull up on the tab to disconnect it from the connector.

    • Carefully remove the circuit board from the phone casing.

  7. YOFCgUMlEIKcOhZp
    YOFCgUMlEIKcOhZp
    cSR6QVdHOG1S4iLL
    1euOcaFADQTJYYGV
    • Hold the front of the phone face down.

    • Using a T6 screwdriver bit, loosen the eight screws holding the keypad protector in place.

    • Loosen the keypad connector by lifting the rectangular plate up with one finger.

  8. YqeuHNKWKim2BQQJ
    YqeuHNKWKim2BQQJ
    PR2yTiEXpMYqGIXn
    F2bXSCNCbWQ3DYc5
    • Use the plastic opening tool to loosen the keypad protector from the faceplate.

    • Once the protector is loosened, use the plastic opening tool to slide the keypad protector towards the screen while pulling on it with two fingers.

    • Remove the keypad protector and connector from the faceplate.

  9. EJ2jRKZgjAqSDuSm
    EJ2jRKZgjAqSDuSm
    VPIQFcZN2lTuHFtP
    • Hold the phone with the keypad facing up and gently push on the keypad with one finger to dislodge it from phone.

    • Place the keypad to the side.

Abschluss

To reassemble your device, follow these instructions in reverse order.

John Miller

Mitglied seit: 22/10/12

50 Reputation

0 Kommentare