Einleitung

If you are unable to use the touchpad of your laptop, use this guide to remove and replace the touchpad.

  1. RnbWapDTJLp2DWG6
    RnbWapDTJLp2DWG6
    bau6hlKh3oCrGO64
    • Turn off your device before starting.

    • Flip the phone over so that the back camera is facing you.

  2. f3qYARdJhbsyX6w6
    f3qYARdJhbsyX6w6
    ITiV1CS1FImQFEkQ
    gqUIRVeQUIkLatEd
    • Use a your hands to remove the backing of the phone.

    • Use your phillips screwdriver to begin removing all the accesible screws.

    • Now begin to remove the coverings above and below the middle plate with your hand.

    • use your hand or a tool to remove the tabbing on the metal plate covering the battery.

    • Remove the metal plate covering the battery.

    • Use your wedging tool to begin removeing the adhesive under the battery.

    • Remove these two screws with your phillips screw driver.

    • Open the two metal tabs

    • Flip the phone back over with the screen facing you.

    • Begin to use the wedging tool to remove the space bar off of the keyboard.

    • remove the screws on each end of the space bars vacant lcoation.

    • Grab the wedging tool and begin wedging the old keyboard.

    • begind wedging the back of the keyboard until free.

    • Begin deperating the keyboard from the backing.

    • grab your replacement keyboard and connect it to the backing of the old keyboard.

    • place the keyboard back onto the front of the phone

    • once placed, hold the keyboard onto the phone while clicking the two metal plates back down to connect the keyboard.

  3. vjy4pMQAhI2UcPPS
    • Use a Phillips #1 screwdriver (PH1 bit) to remove the single 7 mm screw that secures the CD/DVD drive.

  4. tLFxyuonwjQJFmUn
    tLFxyuonwjQJFmUn
    x3aTxOwWkGlXEUQW
    • Slide the CD/DVD Drive out of the laptop.

  5. EJWap42SgrkEnZK6
    • Remove the thirteen 7 mm Phillips screws holding the back cover using the PH1 bit and Magnetic Driver.

  6. KVwFIEXZOn2DHA1R
    KVwFIEXZOn2DHA1R
    EwUFdhmgOrLWqHVc
    • Using the plastic opening tools, separate the back cover from the laptop.

    • It is recommended that you start from a corner and run the tool along the edge of the cover.

    • Be careful not to bend or crack the plastic back cover.

  7. 6xxaQHlUNaRdODGJ
    6xxaQHlUNaRdODGJ
    lAxHaAOmLfXe2EfT
    • Release the clamps holding the white ribbon between the touchpad component and the motherboard.

    • Slide the ribbon from the motherboard connection socket.

  8. yVfIIYWqoExSnWFD
    • Remove the two 7 mm Phillips screws holding the touchpad component to the back panel using the PH1 bit and Magnetic Driver.

  9. UARVK1iKtiZgwZks
    UARVK1iKtiZgwZks
    fhDQBswFeWjv6GQu
    • Release the two clamps connecting the blue ribbon to the external touchpad.

    • Lift the black clasp holding the blue ribbon in place.

  10. jBZirUrIWmYNEUA2
    jBZirUrIWmYNEUA2
    Dgug6GEREkI2rFvD
    • Slide the blue ribbon from the external touchpad holding socket.

    • Lift the touchpad module from the laptop.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Crystal Loomis

Mitglied seit: 22/01/18

732 Reputation

0 Kommentare