Trio Stealth G2 Hype Motherboard Replacement

Geschrieben von: Antoninus Lamptey
  • Kommentare: 2
Trio Stealth G2 Hype Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

5 Minuten

Einleitung

  1. VMNN1qhNQvcXVDMb
    VMNN1qhNQvcXVDMb
    jygNZTQHcAnXmDLX

    • Remove the two 1.2 mm Phillips #0 screws found at the side by the power button.

  2. LXmBlUjmNnLSLTvB

    • Using the plastic opening tool, insert it between the back panel and screen starting on the corner to the right of the power button side and begin separating the back cover.

    • Be cautious when opening the back cover as it is connected through fragile wires to the speaker.

  3. BU2cB1OoaXgfQdYp
    BU2cB1OoaXgfQdYp
    4jq2ttrQomQCTCAg
    f3enDjbADfNpXRZ6

    • Remove the speakers by using your hand to entirely disconnect the back cover.

  4. 5gsj1ayjD2GK36ef
    5gsj1ayjD2GK36ef
    3B3CPZLuyUZ4gQUZ

    • Carefully peel the tape holding down the wires connected to the speaker.

  5. uMu44CMfRbWitOts

    • In order to replace the speakers after they are removed, you must solder the wires back onto the motherboard.

    • The red wire must be soldered onto the "+" terminal while the black wire must be terminal must be soldered onto the "-" terminal.

    • Pull the speaker and wires from the motherboard.

    Where on the mother board do I sober the speaker wires ?

    bombom_buda07 -

    Where on the mother board do I sober the speaker wires

    bombom_buda07 -

  6. 4ejRlP51kn2rUxSw
    4ejRlP51kn2rUxSw
    bpfeZnB32fPRZ3ml

    • While holding the mother board down, slowly remove the battery from tape on the back of the screen.

    • Make sure to keep all wires attached for now.

  7. IKRNLDDFsCEyncMt

    • In order to replace the battery once the wires are removed, you will need to solder the wires of the new battery onto the motherboard.

    • The red wire must be soldered to the "+" terminal while the black is soldered to the "-" terminal.

    • Pull the wires off the motherboard.

  8. kDmIKEBgGbWp6uVn
    kDmIKEBgGbWp6uVn
    MKTxlSQNDs1oTaCX
    K4ZT1c2TUWYyB5C4

    • Peel the black tape located on the left side of the motherboard.

    • Peel the orange tape holding down the wire coming from the bottom left side of the motherboard.

  9. KbQaCbTQKESlbUt1
    KbQaCbTQKESlbUt1
    RAFDsfevhvLTIBy6
    mHoOnJ3OZmUqVHdd

    • The screws to remove the motherboard are located on the top hand side towards the charging port.

    • To reveal the screws, peel of the thin yellow film that covers the whole motherboard just until the screws are accessible.

    • Remove the three 1.2mm Phillips #1 screws using the screwdriver in your 26 Bit Driver Kit.

  10. nVICtajbndMGbAkL
    nVICtajbndMGbAkL
    FYBDNCsFywxrpeXv

    • Remove the orange tape holding the wires to the back of the screen.

    • Simply lift the motherboard of the back of the screen.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Antoninus Lamptey

Mitglied seit: 21/01/15

292 Reputation

0 Kommentare