Whirlpool Refrigerator Water Filter Replacement

Geschrieben von: brenda lopez
  • Kommentare: 3
Whirlpool Refrigerator Water Filter Replacement

Schwierigkeitsgrad

Easy

Schritte

8

Zeitaufwand

10 - 15 Minuten

Einleitung

Over time, a refrigerator’s water filter becomes old and needs a replacement to keep your water clean and healthy. If your water filter replacement light is blinking. Luckily, replacing the water filter in a Whirlpool Side By Side Refrigerator is not difficult at all!

This guide will work for most Whirlpool refrigerators. This guide is written with a model WRS325FDAM04 refrigerator. If you have a different model, you may encounter some minor disassembly differences, but the overall repair process will be the same.

Werkzeuge

  1. uZnovp3POltPPcNl
    uZnovp3POltPPcNl
    EEmEHtDyinkLLTC6
    NpS45AODrJVIyexU

    • Depending on your repair, open one or both doors.

  2. dTeDUFyfe3iV2Eck
    dTeDUFyfe3iV2Eck
    ANSslqw1F6tSLeqV
    JRndAPYsrFatOJqV

    • Pull the water filter door in the base grill open.

  3. EGYcZmClvO5pbC16
    EGYcZmClvO5pbC16
    RBOLKwshKlANiPSZ
    W4f2F1BaF1n2SuUN

    • As the door opens, the filter gets ejected out.

    • When the filter is fully ejected, pull the filter out.

    • A towel is suggested as water might spill while pulling the old filter out.

  4. GkpjGulwmJo13Kvv
    GkpjGulwmJo13Kvv
    TxIdWEcrSMoX3Ana

    • Get the new filter out of its packaging.

    • Remove the covers from the filter inlets. Make sure the O-rings stay on the filter.

  5. obSpgSqZ3eBHrsTW
    obSpgSqZ3eBHrsTW
    uMmilbvcfbcnbc13

    • Align the new filter with the filter housing and insert filter into place.

    • The arrows should be facing the same way.

  6. SYr16vECFLm42lEq
    SYr16vECFLm42lEq
    E3R6MqnyLnKEYfL2
    GZkJfKflQO1p1YJ3

    • Close the filter cover door completely to snap the filter into to place correctly. You will hear a snap!

  7. cNwxFaWLMeGWm6mw
    cNwxFaWLMeGWm6mw
    FZdYObCab1JdcHTp

    • Flush the water system by holding the water dispenser for 5 seconds and releasing for 5 seconds repeating this step until water begins to flow.

    • After water flowing, get at least a total of 3 gallons dispensed in order to see full flushed water results.

  8. VbvgusTsUqfAF24T
    VbvgusTsUqfAF24T
    jveKADlyqJNihbsv
    CySTUDvnuZhOGNne

    • You may need to reset the filter indicator by pushing the switch 5 times in a row.

    • When the filter indicator is reset, the light should change from red to green.

Abschluss

After flushing the water system completely, get ready to have some refreshing water with a cup of ice freshly made with the new installed water filter.

Tinte & Feder

brenda lopez

Mitglied seit: 05/10/21

198 Reputation

3 Kommentare

Changed filter but now water is not coming out of the dispenser. Installed filter correctly per pictures. What could be the problem?

SewFrau58 -

You will have air in the system after changing the filter. Make sure you did turn the water on. Run the water dispenser until water pushes the air out. Run the water until it clears.

Fredric -

Opened the filter door but the filter did not eject. Any troubleshooting advice on how to remove the filter?

Ariana Vega -