Wii U GamePad Lautsprecher tauschen

Geschrieben von: Valentina Cerruty

Kommentare: 16

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

8 - 10 Minuten

Einleitung

Diese Anleitung zeigt, wie die Lautsprecher im Wii U GamePad ausgetauscht werden kann.

Werkzeuge

Ersatzteile

Wii U GamePad Speaker Assembly

Schritt 1

Drehe das GamePad um und entferne die beiden 4,7 mm Schrauben mit einem Kreuzschlitzschraubendreher #00.

tried to unscrew the 10 Tri-Wing size Y1 screw with my iFixIt toolkit

unfortunately the tool is too “fat” and short, it cannot reach 4 screws on the corners of the gamepad.

having the iFixIt toolkit and needing to purchase an additional slim screwdriver it’s a shame…

Antonello Iannone - 07/03/21

Schritt 2

Hebe die Batterieklappe an und entfernen sie.

Schritt 3

Drücke mit deinem Finger nach unten und ziehen sie Akkustecker heraus.
Entferne dann den Akku aus dem Akkufach.

Battery lifts up from the bottom not the top like the photo shows.

Tyler Schommer - 06/10/17

Schritt 4

Entferne die zehn 9 mm Schrauben am äußeren Gehäuse mit einem Tri-Wing Y1 Schraubendreher.
Hebe die Rückseite des Gehäuses an.
Hebe sie vorsichtig an, da der Rumble-Motor auf der Rückseite des Gehäuses immer noch über ein Kabel mit der Hauptplatine verbunden ist.

I used a small blade tip to life up on the black squares that covered the screw holes. Replacing them after.. I skipped that as it seemed impossible they would even stick back down.

Chris - 30/10/18

I am having trouble getting the two screws on the hand grips as the screws are too deep. What should I use to get them?

[deleted] -

I ended up having to buy some cheap amazon screwdrivers and are very disappointed

[deleted] -

Schritt 5

Ziehe mit den Fingern den Stecker des Rumble-Motors am äußeren Gehäuse von der Hauptplatine ab.

Do not pull by the wires! If you do, you better be pretty good at soldering.

Brandon - 10/04/18

I agree. A circle over the plug would have been better as the picture looks like you just pull on the wires lol.

Chris - 30/10/18

Thanks for the comment. I did get a set of tweezers and the negative cable broke anyway. They really could have done a better job at using a different connector for that.

Kristen Bartholomew -

Great. Didn't pull on cord. Whole thing ripped off.

August - 07/05/20

Why in the world is this thing so tightly connected?

Andrew Moore - 10/11/20

Thanks for the comment. I did get a set of tweezers to try to pull it out but still ended up breaking the negative cable. They really could have used a better set of cables and connectors for this.

Kristen Bartholomew -

Schritt 6

Trenne das Kabel zum linken Lautsprecher mit den Fingern ab.

Speakers are connected with solder so removing them is not possible without requiring soldering later on. I left them both connected and instead of removing the motherboard completely I just "hinged" it carefully down to facilitate the work following step 18.

dietcokediva - 11/06/17

Thank you for offering this info because I spent 20 minutes between scratching my head and searching for any alternatives to just the image above, which had a wire nut/housing (and mine certainly did not). As I began to have an anxiety attack (

Missy Leap-Courtney - 06/11/17

Mine also did not have connectors for the speaker. But like mentioned above, I was able to do repair WITHOUT the need to unsolder the speaker wires. Thanks!

Louis Bellanca - 10/12/17