Xbox One Wireless Controller Model 1708 Kappen der Joysticks tauschen

Geschrieben von: Dylan Gross
  • Kommentare: 17
Xbox One Wireless Controller Model 1708 Kappen der Joysticks tauschen

Schwierigkeitsgrad

Mittel

Schritte

7

Zeitaufwand

10 - 15 Minuten

Einleitung

Nach und nach können die Kappen auf den Joysticks des Xbox Kontrollers locker oder klebrig werden. Diese Anleitung zeigt, wie sie ausgebaute und gereinigt oder getauscht werden können.

  1. CZmZL2YuctGTuPJd
    CZmZL2YuctGTuPJd
    KHyRlDiLSFSdhQPm

    • Schiebe die Abdeckung des Akkufachs nach oben und entferne sie.

    • Hebe die Akkus aus dem Akkufachs heraus.

  2. 1RnNtaoQqQZkbY2E
    1RnNtaoQqQZkbY2E
    wVNiZ3TUwVBoC2FL

    • Setze ein Öffnungswerkzeuge aus Kunststoff in die obere Naht ein und arbeite dich dann behutsam nach unten.

    • Heble solange weiter, bis sich die seitliche Abdeckung vom Kontroller löst.

    • Wiederhole für die zweite seitliche Abdeckung.

    Only use a pry tool! The vibration motor wires are exposed and directly accessible from the side when opening. I attempted to open it with a small knife, expecting to be able to gently pry the clips open, accidentally sliced through my right motor’s wires.

    Sawyer Coe -

    Not a sharp of course.

    Kajus Slekys -

    If you have some Guitar picks laying around they work GREAT!

    Mike Beane -

  3. S6rlXDDRcqlumZ32

    • Ziehe den Aufkleber im Akkufachs vorsichtig ab oder öffne das Loch in der Mitte, um an die verborgene Schraube darunter heranzukommen.

    • Entferne die fünf 9 mm Torx Sicherheitsschrauben auf der Rückseite.

    Torx-8 security bits work as well.

    jahiamir -

    Torx 8 or 9 wasn’t working. I used 2.0 minus screwdriver

    richjlee -

    The 2.0 minus worked for me as well.

    metric -

    When sliding in the plastic cover during reassembly be sure it lines up with the battery compartment contacts. It can be really easy to not see it and bend the contacts. If you still encounter force during this step, depressing the triggers out of the way worked for me.

    Drew -

    Since mine is out of warranty I just broke out the security nib with a 2.0 standard bit. Then used a T8 torx.

    Tim LaCrosse -

  4. kfdJ5aNuDEUk4QSv
    kfdJ5aNuDEUk4QSv
    EaxhK2qZKFPa2bSP
    uLhJmZMFjIR1fmmF

    • Befestige die Rüttelmotoren mit einem Klebeband.

    • So können die Motoren nicht herausfallen.

  5. iqgdKTgD5ghZ2AiA
    iqgdKTgD5ghZ2AiA
    k5hd4bkef3GQZcnV

    • Drehe den Kontroller so, dass die Abdeckplatte nach oben zeigt.

    • Hebe die obere Abdeckung ab.

  6. jALZRgrIkQxcoU2w

    • Drehe den Kontroller um und hebe vorsichtig die Rückseite ab.

    • Achte auf die Vibrationsmotoren, sie fallen leicht heraus und könnten die Platine beschädigen.

    Reassembly: When placing the back cover on: notice that the battery terminals need to slide inside the cover first. Then compress the triggers slightly, Then the cover will be aligned correctly. Then add the front cover and add screws so it doesn’t come undone.

    hunteil -

  7. SBpFEREdAboEdgLe

    • Ziehe die Kappen von den Joysticks ab.

    Are the joystick potentiometers soldered to the mother board or just push fit, this guide doesn’t mention soldering so I’m assuming the latter?

    Can you get genuine replacement joystick potentiometers as I’ve only seen cheap eBay type ones?

    Alan -

    The actual joysticks themselves are soldered into the bottom motherboard.

    Bryan Remely -

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

Tinte & Feder

Dylan Gross

Mitglied seit: 25/09/17

4590 Reputation

6 Kommentare

How about the square thing with the stick and hinges that the joystick is attached to? I think it’s called the Module. I have a joystick drift / drifting problem and that may help me out. Thanks.

Cory C -

Agreed. That’s actually the part I need to replace too. The module.

Thomas Tomchak -

followed this guide to take the controller apart because I had a joystick that was sticking, my solution was to put some 3in1 oil on the module that was sticking and it seems to be working a lot better now.

John Jaggi -

@corytc and @tomchak I did replace the module, in general, you buy (Amazon or eBay) you will receive a module of 6 modules you need a multimeter and test each module interface, measure both resistances and subtract them, the one nearest zero is the module you will use since is the one with least drift from the factory.

Just disassemble it, turn upside down uses a solder remover and unsolder the old one, place the new one solder back, boom you are done.

Like you will need an iron solder with medium and thin tips, I used lead-free solder, so is a patience test, be careful with the wires from the rumbles, try not to unsolder them since is a thin wire and is difficult, like I have big hands so took me a while to solder back.

Luis Vitorio Cargnini -

Just want to say the hardest part is carefully prying off the plastic covers on the handles. It’s also not necessary to remove the back cover for simply replacing the joysticks. Other than that, it’s very easy. I would guess this is rated at moderate difficulty simply due to the plastic covers.

Will -

Where can one get the replacement joysticks ?

Keven Dubois -