Xbox One Wireless Controller Model 1708 Steuerkreuz tauschen

Geschrieben von: Dylan Gross
  • Kommentare: 17
Xbox One Wireless Controller Model 1708 Steuerkreuz tauschen

Schwierigkeitsgrad

Mittel

Schritte

7

Zeitaufwand

9 Minuten

Einleitung

Nach und nach kann das Steuerkreuz des Xbox Kontrollers locker oder klebrig werden. Diese Anleitung zeigt, wie es ausgebaute und gereinigt oder getauscht werden kann.

  1. CZmZL2YuctGTuPJd
    CZmZL2YuctGTuPJd
    KHyRlDiLSFSdhQPm

    • Schiebe die Abdeckung des Akkufachs nach oben und entferne sie.

    • Hebe die Akkus aus dem Akkufachs heraus.

  2. 1RnNtaoQqQZkbY2E
    1RnNtaoQqQZkbY2E
    wVNiZ3TUwVBoC2FL

    • Setze ein Öffnungswerkzeuge aus Kunststoff in die obere Naht ein und arbeite dich dann behutsam nach unten.

    • Heble solange weiter, bis sich die seitliche Abdeckung vom Kontroller löst.

    • Wiederhole für die zweite seitliche Abdeckung.

    Only use a pry tool! The vibration motor wires are exposed and directly accessible from the side when opening. I attempted to open it with a small knife, expecting to be able to gently pry the clips open, accidentally sliced through my right motor’s wires.

    Sawyer Coe -

    Not a sharp of course.

    Kajus Slekys -

    If you have some Guitar picks laying around they work GREAT!

    Mike Beane -

  3. S6rlXDDRcqlumZ32

    • Ziehe den Aufkleber im Akkufachs vorsichtig ab oder öffne das Loch in der Mitte, um an die verborgene Schraube darunter heranzukommen.

    • Entferne die fünf 9 mm Torx Sicherheitsschrauben auf der Rückseite.

    Torx-8 security bits work as well.

    jahiamir -

    Torx 8 or 9 wasn’t working. I used 2.0 minus screwdriver

    richjlee -

    The 2.0 minus worked for me as well.

    metric -

    When sliding in the plastic cover during reassembly be sure it lines up with the battery compartment contacts. It can be really easy to not see it and bend the contacts. If you still encounter force during this step, depressing the triggers out of the way worked for me.

    Drew -

    Since mine is out of warranty I just broke out the security nib with a 2.0 standard bit. Then used a T8 torx.

    Tim LaCrosse -

  4. kfdJ5aNuDEUk4QSv
    kfdJ5aNuDEUk4QSv
    EaxhK2qZKFPa2bSP
    uLhJmZMFjIR1fmmF

    • Befestige die Rüttelmotoren mit einem Klebeband.

    • So können die Motoren nicht herausfallen.

  5. iqgdKTgD5ghZ2AiA
    iqgdKTgD5ghZ2AiA
    k5hd4bkef3GQZcnV

    • Drehe den Kontroller so, dass die Abdeckplatte nach oben zeigt.

    • Hebe die obere Abdeckung ab.

  6. jALZRgrIkQxcoU2w

    • Drehe den Kontroller um und hebe vorsichtig die Rückseite ab.

    • Achte auf die Vibrationsmotoren, sie fallen leicht heraus und könnten die Platine beschädigen.

    Reassembly: When placing the back cover on: notice that the battery terminals need to slide inside the cover first. Then compress the triggers slightly, Then the cover will be aligned correctly. Then add the front cover and add screws so it doesn’t come undone.

    hunteil -

  7. K1gPMYdctQwIjRAw

    • Drehe das Gerät um und ziehe das Steuerkreuz vorsichtig ab.

    It needs to be made a little clearer that the thin metal retaining ring needs to be unclipped before pulling on the D-pad. A small, flatbladed screwdriver did it nicely for me.

    Paul Hough -

    As mentioned above, clarification is needed that the metal ring is intended to lay on top of the DPad - you should remove it first when disassembling, and it should be installed after the DPad to hold the DPad down when re-assembling.

    Additionally, the DPad is oriented so that the directional button without an extended tab on the end is on the bottom (down).

    sonofray -

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

Tinte & Feder

Dylan Gross

Mitglied seit: 25/09/17

4590 Reputation

6 Kommentare

Will one of the D-pads from the Xbox One controller model 1698 fit and work with the Xbox One-S controller model 1708. I have been looking all over the net for a replacement D-pad and other buttons like the RB, LB Bumper setup and I have had absolutely no luck finding replacement D-pads or other buttons specifically designed for the Xbox One-S controller. I would greatly appreciate your help.

Walter “Biggdubbya” Kloster -

My D-pad was not working properly so I dropped drops of alcohol and other cleaners to fix the issue since the screws inside my controller were stripped and I was unable to open it and at the beginning it worked but then It started failing again so I did it again and this time the left direction is dead. I sent it to be repaired and they told it couldn't be salvaged yet they repaired the thumbsticks just to force me to pay them.

Diego Jose -

The D-pad on our controller sticks. I disassembled the device and discovered one of the small metal pieces that are supposed to spring back after the button is pressed has been deformed. I will need new ones, but I don’t know what to call the part or where to get it, but I’m sure it’s pennies? Any suggestions? I’d add a photo if I could here.

Joseph Greer -

Search for “Xbox One Controller Replacement D-Pad Button Metal Dome Conductive Film Sticker” on Amazon, NewEgg or Ebay. Should cost 5-10 bucks. Cheaper if you get it shipped from China, but takes forever.

Sudil Mahendra -

Incomplete guide making it useless and I am pretty sure someone else can do better

Jason Bouchard -

estou com um problema no meu controle. quando pressiono o D-Pad para esquerda ele vai para a esquerda e para cima, quando pressiono para cima ela vai para cima e para esquerda. Como posso resolver esse problema? qual peça tenho que trocar?

djandersonroots_alves -