Einleitung

Teaching you how to replace a crack screen.

  1. xJUUJwopcyqjUmfy
    • Remove the two bottom screws.

    • The two bottom screws have a 2.44mm wide tops and are 5.44mm.

  2. NInYVRRDWjbNrCHq
    NInYVRRDWjbNrCHq
    E2vJZMqdFxTX2NIt
    • Slide the spludger between the screen's rolled edge and the back of the tablet and pry apart carefully. Expect the tablet screen to make a cracking sound.

    • Slide the spudger in the slit all the way around the perimeter of the tablet to fully separate the screen.

  3. QUtCZJabAFVVXNER
    • Once the screen has fully separated from the back of the tablet, gently lift up the edges to remove the screen.

  4. HjPThFDnGvMPIbAr
    HjPThFDnGvMPIbAr
    pxKQkM3oDtmIOCPc
    • Next, disconnect the front facing camera ribbon (shown). The ribbon is held to the motherboard by a small bar.

    • Using the spudger to pry open the bar, pull the ribbon out to disconnect it.

  5. M1jgSKvnaMffnHYP
    M1jgSKvnaMffnHYP
    t4x34stPyIdQ4jgP
    • Next, work on disconnecting the ribbon for the touch screen.

    • The touch screen ribbon is larger than the camera ribbon and is located on the left side of motherboard.

    • Using the spudger, gently pry the ribbon out from under the bar. Pull the ribbon and disconnect it from the motherboard.

  6. FND2YFTGCZW5BerK
    FND2YFTGCZW5BerK
    HV4gcOknLWA2StQ6
    lamLwSxoBRhDa6kB
    • Next, work to disconnect the LCD screen ribbon.

    • This ribbon is located on the right side of the motherboard.

    • The ribbon is connected to the motherboard by a small bar. Using the spudger, pry the bar apart and slide the ribbon out.

  7. tAEX5aRAd4r3JNNd
    tAEX5aRAd4r3JNNd
    CZa2XABnJAlRQ4Oo
    W2rSeTjW1XEODuQE
    • Remove the two motherboard screws.

    • To remove the first screw, expose the black strip. Then using a Philips head screwdriver, remove the first screw.

    • Locate the second screw by looking to the bottom right of the motherboard. Remove the second screw with the Philips head screwdriver.

  8. SGUB11mD5hHDx1Bc
    SGUB11mD5hHDx1Bc
    OJNgSgKHUHXfp1fJ
    • Locate the last connection to the LCD in the top right section of the tablet.

    • The last connection is a ribbon connected to green wire, which is held down by tape.

    • Disconnect the ribbon by removing the tape connecting it to the plastic frame of the tablet.

  9. kxGJUDBNKu1EdOGt
    • With the spudger, pry the LCD screen from the plastic screen holder.

    • Use gentle, but firm force to pry the LCD away from the holder.

  10. nLmmAfmAhsuWkWRa
    • Work the spudger all the way around until the LCD is free from the screen holder.

  11. SXD4XqySoDMCwJ13
    • Finally, lift the LCD off, removing it from the screen holder and the motherboard.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Marcus Nelson

Mitglied seit: 26/03/15

307 Reputation

0 Kommentare