iBook G3 14" Display Data Cable Replacement

Schritt 1

Use a coin to rotate the battery locking screw 90 degrees clockwise.
Lift the battery out of the computer.

Schritt 2

Pull the keyboard release tabs (highlighted in red) toward you and lift up on the keyboard until it pops free.
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again.
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.

Schritt 3

If your computer does not have an AirPort card installed, skip to the RAM shield removal step.
Push the wire clasp toward the AirPort card and pull it up to free it from the RAM shield.

Schritt 4

Grasp the clear plastic tab on the AirPort card and pull toward the right.

Schritt 5

Hold the AirPort card in one hand and use your other hand to remove the antenna cable.

Schritt 6

Remove the two Phillips screws that secure the RAM shield.

Schritt 7

Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.

Schritt 8

Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.

Schritt 9

Use a pin to remove the three rubber feet from the lower case.

Schritt 10

Remove the three newly-revealed Phillips screws.

Schritt 11

Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.

Schritt 12

Remove the three hex screws using a T8 Torx screwdriver.
The screw in the center is shorter than the other two.

Schritt 13

Remove the two Phillips screws on either side of the battery contacts.

Schritt 14

Breathe deeply. Trying times are ahead, but we promise the lower case does come off.
Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.

Schritt 15

There is a slot on the wall of the battery compartment that locks the lower case in place.
Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

Schritt 16

Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case.
Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

Schritt 17

Continue to run the spudger around the front, right corner.
There are two tabs on the port side of the computer, one near the front corner and one near the sound out port.

Schritt 18

Once the front and sides of the lower case are free, turn the computer so that the back is facing you.
Pull the lower case up and toward you until the back tabs pop free.
It may be helpful to jiggle the case up and down.

Schritt 19

Remove the small greasy springs with white plastic caps from either side of the battery contacts.

Schritt 20

All of the screws in the following step have small heads - the screws with larger heads hold the bottom shield on.
Remove the following 9 screws on the bottom of the computer:
Three 3 mm Phillips around the battery compartment.
Three 5 mm Phillips on the left and bottom edges.
Three 14.5 mm Phillips on the top and right edges (you may have to peel back the foil tape to reveal the screw near the security lock slot).

Schritt 21

Turn over the computer and open it.
Pry up the magnet covering a Phillips screw near the middle of the computer.
You may need to peel back the serial number sticker to access the magnet.

Mine didn't have a screw under the magnet.

TekMac -

Zitat von TekMac:

Mine didn't have a screw under the magnet.

I don't mean that a screw was missing, I'm saying that there is no screw or screw hole installed on my 14" in that location. The other steps were dead-on though.

TekMac -

No magnet, screw or screw hole on my upper case either.

randy3833 -

Not all G3 Dual USB iBooks have a screw underneath the magnet, so the magnet need not be removed in these cases and will not hinder the removal of the top.

Brett Fox -

Some iBooks like the 16 VRAM model have the magnet but there is no screw behind it.

Alex -

Check to see if your model has a screw under the magnet first. If you can lift up the area around the magnet there is no screw to deal with.

James Scanlan -

Schritt 22

Remove the following 3 screws on the edges of the keyboard area:
Two 6 mm Phillips underneath the keyboard area.
One 9 mm Phillips above the keyboard area.
On some models, there may also be a screw under the magnet you just removed. If so, remove the screw at this point.

There is a forth screw underneath the magnet: top center of keyboard area.

tkn77 -

Schritt 23

This is a diagram of the ribbon clamp connectors you will disconnect in the next step.
With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
After disengaging the locking bar, slide the cable out of the connector.

Schritt 24

Loosen the trackpad connector by pulling the top piece up slightly, freeing the trackpad ribbon.
Slide the orange trackpad ribbon out of the connector.

Schritt 25

Use a straightened paperclip to open the optical drive tray, and pull it out about halfway.

Schritt 26

Don't lift the upper case off the computer yet as there are still two cables left to disconnect.
Lift the upper case from the left side and use your other hand to pull out the right side in order to clear the power receptacle.

Schritt 27

The connectors at the ends of the cables are attached very firmly to the sockets on the logic board. Pulling directly on the cable will either separate the cable from its connector or the socket from the logic board.
Lift the upper case enough to disconnect the blue and white power cable from the logic board.
Using your fingernails or a dental pick, carefully pry the connector from its socket.
Make sure you are pulling only on the connector and not on the socket.

hello...while i was at step 27 i pulled the connector too much and i broken the socket from the logic board!! I used a glue to put it back but now doesen't turn on the computer...any idea??? :)

Fabrizio -

Schritt 28

Lift the upper case off completely and disconnect the red and black speaker cable from the logic board.
Make sure you are pulling only on the connector and not on the socket.

Schritt 29

Remove the following 16 screws:
Five 3 mm Phillips (these have smaller heads than the others).
Three 5 mm Phillips.
Eight 6 mm Phillips.

Schritt 30

If you have already removed the yellow tape, skip this step.
Peel back three strips of yellow tape in the bottom, left corner.
Peel back one strip of foil tape near the audio-out port, one near where the trackpad connects to the logic board, and one near where the screen latch used to be.

Schritt 31

Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.

Schritt 32

If you have already removed the hard drive, ignore its presence in the following steps. The hard drive does not affect the display removal.
Disconnect the microphone cable from the front, left corner of the logic board.
Peel back the black tape and free the microphone cable from the hard drive.

Schritt 33

Use the black plastic handle to disconnect the display data cable from the logic board.

Schritt 34

If you have already removed the modem, you will only need to remove one of these screws.
Remove the two Phillips screws securing the display data cable to the metal framework.

Schritt 35

Deroute the display data and microphone cables, removing tape as necessary.

Schritt 36

Peel back the yellow tape securing the inverter cable to the metal framework.

Schritt 37

Disconnect the inverter cable from the logic board.
Carefully deroute the inverter cable from beneath the optical drive.

Schritt 38

Deroute the AirPort antenna cable from beneath the optical drive.

Schritt 39

Support the display with your free hand removing the following screws.
Remove the single Phillips screw on the outer edge of either hinge (two screws total).
Tilt the display back to get over two small nubbins, and then slide it directly from the case and away.

Schritt 40

Use a 1.5 mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).
If you don't have a 1.5 mm hex driver, you can probably get these screws out with a T6 Torx screwdriver. However, if you use a T6 Torx driver you'll be more likely to strip the screws.

Schritt 41

Use your thumbs to slightly separate the rear bezel from the front bezel.
It is helpful to hold the opposing corner of the display stationary to aid in flexing the rear bezel away from the display.

Schritt 42

Insert the flat end of a spudger into the gap between the front and rear bezels.
Rotate your spudger until it is parallel to the front face of the display.
Run the spudger around the perimeter of the display to separate the rear bezel from its retaining clips.

Schritt 43

Lift the rear bezel off the display.

Schritt 44

Remove the pieces of readily removable tape from around the perimeter of the display.
Carefully remove the aluminum tape covering the display data cable connection.

Schritt 45

Remove the single screw inserted through the piece of EMI tape near the bottom edge of the display.
Use the tip of a spudger to remove the small washer under the screw you just removed.

Schritt 46

Peel the aluminum/EMI tape off the cast aluminum frame of the clutch hinges.
It is not necessary to peel the tape off the thin steel LCD cover.

Schritt 47

Remove the two Phillips screws securing each side of the LCD to the clutch hinge frame (four screws total).

Schritt 48

Lift the thin steel LCD cover off the LCD.

Schritt 49

Remove the second of the two Phillips screws securing the clutch cover to the cast aluminum frame of the clutch hinges.

Schritt 50

Pull the clutch cover away from the front of the display.
Keep track of the two covers that close the ends of the clutch cover. The third picture shows their correct orientation on the clutch cover.

Schritt 51

Remove the pieces of tape covering the display data and microphone cables near the bottom edge of the display.

Schritt 52

Disconnect the display data cable by pulling its connector away from the socket on the LCD.
Pull the connector parallel to the face of the LCD.
Remove the display data cable from the display.

Schritt 53

Use the tip of a spudger to lift the microphone out of the front bezel.
De-route the microphone cable from around the top and side of the display.

Schritt 54

Remove the display data cable from the display.

iBook G3 14" Display Data Cable Replacement

Einleitung

Werkzeuge

Ersatzteile

0 Kommentare