Galaxy Watch Active2 Haupteinheit entfernen

Geschrieben von: Tobias Isakeit

Kommentare: 22

Galaxy Watch Active2 Haupteinheit entfernen

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

25 - 45 Minuten

Einleitung

Diese Anleitung zeigt, wie die Haupteinheit in der Samsung Galaxy Watch Active2 ausgebaut werden kann.

Werkzeuge

Schritt 1

Drücke und halte die untere Taste an der Samsung Galaxy Watch Active2 etwa 3 Sekunden lang, bis sie sich ausschaltet. Du solltest ein kurzes Vibrieren spüren.
Wenn das "Ausschaltsymbol (Power off)" erscheint, dann drücke auf die Mitte des Displays, bis die Uhr herunterfährt. Diesmal solltest du zur Bestätigung ein längeres Vibrieren erhalten.

How can you power off the device without being able to interact with or see the broken display you're fixing?

Dylan Hill -

Schritt 2

Entferne die vier 4 mm langen Tri-Point-Schrauben Y00 auf der Rückseite der Uhr.

Y1.5 works just as good

BRIAN MIRANDA -

Bekomme ich nicht auf … Schrauben zu fest

Tino Wehner -

The screws are attached to the cover. So you just need to loose them, not remove them.

Yonic Surny -

Any tips for a too tight screw ?

Daisy Doune -

Schritt 3

Setze ein Plektrum in der Nähe der Tasten zwischen die Kunststoffrückseite und das Metallgehäuse.
Drücke das Plektrum hinein, bis sich die Rückseite vom Gehäuse löst.
Entferne die Rückseite jetzt noch nicht. Sie ist noch mit einem Kabel am Motherboard angeschlossen.

There is a glue-ish gasket keeping it closed. I used an exacto knife to start it opening.

BRIAN MIRANDA -

This was super helpful thank you! Perfect timing

this is trash -

It worked perfektly for me, but i damaged the metal part. So do it really carefully.

Theo Storch -

Waarmee kan ik de achterste oplaadplaat weer vast lijmen op de achterste behuizing

Ilona Smit -

What glue do i use to replace the glue on the back cover? The kit I bought only came with the front glass seal.

David Dickinson (Blondie) -

Schritt 4

Hebe die Rückseite vorsichtig hoch, um an den Stecker der Sensorgruppe heranzukommen.
Trenne den Stecker der Sensorgruppe mit einem Spudger vom Motherboard ab.

Ou je peu me procurer le tourne vis tri point 000

grenierlulu -

Schritt 5

Entferne die Rückseite.

Where would you recommend buying a new back panel/charger?

Nathan Williams -

Una pregunta. y para poner el reemplazo sería necesario algún tipo de sellador o silicón?porque pues usualmente este tipo de tapas vienen sellados de fabrica para evitar cualquier posibilidad de que le pudiera entrar agua

Jesus Frias -

Schritt 6

Trenne das Display und den Lautsprecher mit einem Spudger ab.

Schritt 7

Trenne den Luftdrucksensor, die Tasten und das Mikrofon mit dem Spudger ab.

Schritt 8

Setze einen Spudger oben rechts, nahe beim Displaystecker, unter das Motherboard ein.
Verdrehe und hebe den Spudger ein wenig, um die Haupteinheit zu lösen.
Es kann hilfreich sein, die Kommentare zu diesem und dem nächsten Schritt durchzulesen, falls du Schwierigkeiten hast.

I would not suggest to do so. There are components underneath the motherboard as well. There are none in this specific corner, but the core assembly does not come out that easily and people might try other corners and positions. Rather unscrew the motherboard and remove the battery from the core assembly directly.

Nicola Tambascia - 09/08/22

Yes! I was unable to remove the motherboard as pictured unless the screw was removed (Step 12). I suggest a re-ordering of steps in this guide.

Jerry Rattanong -

You have to sort of wiggle it up from all sides and gradually lift out the corner/sides adjacent to the spludger as shown. I took a few minutes doing it carefully, it's fairly snug. Avoid pulling the motherboard out from only one side if you must at your risk.

Future Zen - 01/04/25

explain to not lift only the green board, i broke some flex between the green board and the battery holder under the green board

, its not unplugable, now i have to wield it back

Justin Alvarez Cepeda -

Schritt 9

Fasse die Haupteinheit behutsam an und schiebe sie unter den Kabeln heraus.
Entferne die Haupteinheit.

I had to remove that screw on the core assembly using a Phillips 000. When I initially tried lifting, the core assembly started to bend. Mine also has a connector under the core assembly near the thumb in the picture. The connector goes from the underside of the core assembly to the screen/body. It prevents me from removing the core assembly as I'm not sure how it should be removed examining it

Louis Finney - 20/09/21

This step is really difficult, and I'm still not sure it was necessary. The core assembly is really packed in there, and it took me several attempts, lifting from various corners. Don't pull by the circuit board. It will bend if you're not careful. You've got to get under the core assembly. I had the most luck starting next to the display connector at the top, then moving to the sensor on the other end of the board (barometric sensor), then moving to the speakers on the left, and finally lifting from multiple points once it was out far enough. In really hoping I didn't damage anything.

Karl Arp - 27/05/22

I think the comments here should be added to the step before.

Nicola Tambascia -

I would be very careful following Louis Finney's advice above. They are describing detaching the motherboard from the core assembly which also includes the battery and internal frame. Removing the motherboard from the rest of the core assembly exposes a very delicate looking ribbon cable that I nearly tore by trying to remove the screw holding the motherboard in place.

As Karl Arp notes, trying to pry the core assembly up by the motherboard feels like it puts a lot of strain on the circuit board, so it might be necessary to go at it from multiple angles.

Removing the whole core assembly was very difficult, and required a lot more force than I was expecting, and I had the luxury of being able to approach it from both sides, as the screen had already detached from the device (hence the need to repair), and still found it very challenging.

I would advise, at a minimum applying mild heat to the metal outer frame to hopefully cause it to expand and give some additional clearance.

Philip Hickey -

Goede middag hier bij stap 10 is het fout gegaan bij mij,

De knop waar je hem mee aan uit zet is afgebroken snik snik.

Nu lig ik eruit.

Maar de uitleg die je geeft is prefect kan niet beter.

Vraag is er nog hoop voor mij..

B.v.D.

Wim Roks -