Lenovo ThinkPad X1 Carbon 6. Generation Lautsprecher tauschen

Geschrieben von: Aaron J Houston

Kommentare: 16

Lenovo ThinkPad X1 Carbon 6. Generation Lautsprecher tauschen

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

1 Minute

Einleitung

Werkzeuge

Ersatzteile

Lenovo ThinkPad X1 Carbon Gen 5 and 6 Replacement Battery

Schritt 1

Benutze einen Kreuzschlitzschraubendreher #0, um die fünf Schrauben zu entfernen, mit denen die Rückseite befestigt ist.
Die Schrauben lassen sich nicht komplett aus der Rückseite entfernen. Lockere sie also einfach soweit es geht.

Schritt 2

Benutze einen Jimmy, um die Rückseite direkt an den Fixierstiften anzuheben.
Auch wenn im Bild ein Metallwerkzeug zu sehen ist, empfehlen wir ein Öffnungswerkzeug aus Kunststoff zu verwenden, um eventuelle Schäden zu minimieren.
Entferne nun die Rückseite.
Falls du beim Anheben der Rückseite Widerstand spürst, kontrolliere die Schrauben und stelle sicher, dass sie komplett gelöst sind.

I thank you for these instructions. They were quite helpful and I successfully replaced the fan. There is one thing however. Your instructions stated the following: "Be sure to pull on all of the cables at the same time."

I disagree. One should never pull the wires. I was able to nudge the one part of the connector loose from the other part that it fit into." I then put the new fan in and gently and carefully pushed the connecting parts together.

Otherwise, your instructions were clear and to the point. Thank you very much

ALAN L SILBERLIGHT -

The image shows prying the cover open at the bottom right. In fact, there are tabs securing the bottom edge to the frame. The cover needs to be pried open at the top edge. Once the top edge is released, the cover can be shifted slightly toward the top of the image to disengage the tabs at the bottom.

This error, along with the similar error about removing the battery in step 4, suggests that the instructions were written with the laptop in the opposite orientation than what is shown in the images.

EatCroc3 -

I also don't believe that the iFixit Jimmy is necessary - in fact, it might scratch up the exterior paint of the X1 Carbon Gen 6. Instead, I find the triangular iFixit picks are more appropriate for the task: iFixit Plektren (6er Pack)

Also, at least for my unit, the lid comes off easily and I only use the plastic picks if there's any resistance and I don't want to risk breaking any of the clips.

Tai Lam -

Schritt 3

Benutze einen Kreuzschlitzschraubendreher #0, um die vier 5 mm Schrauben zu entfernen, mit denen der Akku am Gehäuse befestigt ist.

The screw holes do not align 100%. Dont tighten all the screws as you re-insert them, leave just a little bit of play so that you can push the battery slightly until all the screws fit nicely, then tighten them. A little bit of DIY wisdom helps here. :-)

Michael Dauer -

Schritt 4

Entferne jetzt den Akku, indem du ihn an der Oberkante des Laptops anhebst und dann vom Motherboard weg ziehst.

Recommend changing the command language to lifting from the TOP edge, as the BOTTOM edge is secured.

Alexander Van Auker - 07/10/20

Thank you, was wondering what I'm doing wrong

Ash Weber-Campbell -

Agreed, the original description is misleading at best, wrong at worst!

Victor Vojtech Terber -

You forgot to tell people to disconnect the battery from the motherboard before removing…

Becky - 31/03/21

Agree with both comments above: lift from top left and top right of battery. This disconnects it and it lifts out and away.

Marc G -

In my 6th generation X1 Carbon there are two wires that are routed on the edge of the battery and have to be moved out of the way. These are antenna cables, be gentle with them, kinks and indents change their high frequency properties and may lead to problems with your WIFI.

Michael Dauer -

Before removing laptop cover you can disable the battery in the bios before beginning work for extra safety. Battery will be re-enabled at next startup automatically.

Darryl S -

How do I know the generation of my X1 Carbon?

Does this batter fit all generations?

eric gofreed - 12/03/23

The generation info of Lenovo ThinkPad X1 Carbon is marked on the back cover (i.e., 6th Generation), with shiny black color (ink ?), near the fan's openings.

The battery's original PN for 6th gen is ASM P/N SB10K97587 (FRU P/N 01AV430), marked visible on the battery (after removing the back cover).

vsm -

The #0 Phillips screwdriver furnished with the kit was not well machined; it threatened to strip out the Phillips cross-grooves.

Fortunately, in my own toolbox I had a robust and well machined #0 screwdriver, and was able to remove the battery screws without stripping the grooves.

Otherwise, the kit was excellent.

Roger Mehle - 10/23/23

Roger Mehle -

Hi @rogermehle, I'm very sorry to hear about the Phillips #0 screwdriver trouble. If you would like to reach out to our Customer Support team via help.ifixit.com, they will be able to assist you. Thank you for letting us know. We're happy your repair was a success overall : )

Sarah Westberg -

Yes top edge lift. Can't they change this?

Ravi Sawhney -