Motherboard entfernen

Schritt 1

Ziehe das Ladekabel ab und schalte deinen Controller aus, bevor du beginnst.
Stecke ein Plektrum unter die untere rechte Ecke der Abdeckung, um die Clips zu lösen, mit denen sie befestigt ist.

What if i accidentally press the playstation button during the repair

@elias30038 I just hit the circle button and that powered it back off. I think you mostly just need to be careful about it not turning on once you get the electronics exposed at the end.

Alex B -

Schritt 2

Schiebe das Plektrum an der unteren rechten Kante entlang, um die Clips zu lösen, die die Abdeckung festhalten.

Schritt 3

Stecke ein Plektrum unter die untere linke Ecke der Abdeckung, um die Clips zu lösen, mit denen sie befestigt ist.

Schritt 4

Schiebe das Plektrum an der unteren linken Kante entlang, um die Clips zu lösen, die die Abdeckung festhalten.

Schritt 5

Hebe die Abdeckung mit deinen Fingern an der unteren Kante an, um die restlichen Clips zu lösen.
Hebe die Abdeckung über die Joysticks, um sie zu entfernen.

Schritt 6

Fasse den Kontroller mit einer Hand und halte den linken Auslöser mit dem Daumen gedrückt.
Setze das flache Ende des Spudgers mit der anderen Hand zwischen die L1 und L2 Tasten ein.
Heble die L1 Taste mit dem Spudger behutsam vom Kontroller weg, halte dabei den Finger darüber, damit die Taste nicht davonspringen kann.

Tried prying from the front of the buttons as pictured and my spudger broke off in the gap. A video I watched showed them being pried off from the back (between the R1/R2 and L1/L2 buttons) which seemed much easier.

Lora Singleton -

Agree with Lora's comment above. I was able to use an old credit card to take L1/R1 out this way. I pressed down the L2/R2 button to create space to work in, then came in from between L1/L2 and R1/R2. It's easy to pop one of the outer corners first then you can work the credit card around the top and the rest falls out.

darkstar448 -

Man, if I'd just read the thumb part...

caldugen -

erst überlegen, und dann....

Oliver -

Schritt 7

Wiederhole den vorherigen Schritt für die R1 Taste.

to save a few bucks, the L1 and R1 buttons can be removed without the use of the spudger tool by using any thin prying tool and just pry the buttons from the bottom instead of the top

Alan Peng -

What I didn't see addressed anywhere (here or in other similar articles) is that replacement R1 / L1 buttons can be differ enough to be un-usable depending on which model your ps5 controller is. The ones I ordered don't fit and now I can't find a way to be sure I get the right ones because few know there's even a difference.

Walt Mather -

Did you already figured it out? The version the we need yo use?, We are in the same situation here.

Gerald Ross Rodriguez -

Tried prying from the front of the buttons as pictured and my spudger broke off in the gap. A video I watched showed them being pried off from the back (between the R1/R2 and L1/L2 buttons) which seemed much easier.

Lora Singleton -

Schritt 8

Entferne die beiden 6,4 mm Kreuzschlitzschrauben, die die unteren Enden des Gehäuseunterteils fixieren.

Schritt 9

Entferne die beiden 6,4 mm Kreuzschlitzschrauben hinter den L1 und R1 Tasten.

Schritt 10

Sei sehr vorsichtig beim Ablösen der Clips an der Gehäuserückseite - sie sind sehr empfindlich und gehen leicht kaputt.
Löse die beiden Clips links und rechts von der Kopfhörerbuchse mit der Spitze des Spudgers.

Schritt 11

Die Gehäuserückseite ist an der linken und rechten Seitenkante mit fest sitzenden Kunststoffclips befestigt.
Setze einen Spudger mit dem flachen Ende zwischen das vordere und hintere Gehäuseteil ziemlich unten an der linken Kante.
Schiebe den Spudger an der linken Kante entlang und drücke die Gehäuseteile auseinander, um die Clips zu lösen.

Be careful when prying into the shell because i damaged mine prying it open too forcefully

Elias -

there is two screws if its too hard to open it up at the end of it

samaka - 25/10/25

Schritt 12

Löse auf gleiche Weise die Clips an der rechten Kante.

Schritt 13

Lege den Kontroller mit der Rückseite nach oben, so dass die Joysticks auf der Arbeitsfläche liegen.
Halte den Kontroller mit den Fingern nach unten und hebe die Gehäuserückseite mit den Daumen nach oben ab.

Schritt 14

Entferne das Gehäuseunterteil.

There are four more clips/hooks hidden in the seams along the outer sides of the handles. If you pull open the controller as shown in this step, then you will shear off the two tiny clips which are right next to the R1 and L1 buttons.

Therefore, you should first release those clips by prying the seams open sideways.

I noticed this with the updated design of the controller, not sure whether the hooks are present on the first version.

The hooks are not critical for the integrity of the controller as the two halves are held together by the screws hidden under the buttons. The damage does show that the controller has been taken apart.

Nick -

Thought I'd clarify: The clips next to the L1 and R1 are on the outer side from the L1 and R1 buttons, I'd suggest zooming in on the picture to see them. They're quite easy to break, but also easy to remove using the plastic spudger along the seam, bending the bottom cover outwards

Franz Rolfsvaag -

I am still strugling to find the clips. Could someone point them out in the image with a screen shot or something like that.

aGingerThing -

I keep getting stuck at this step too with the new DualSense CFI-ZCT1WA revision. The top and bottom shells seem like they are fused together next to L1/R1 but I can't seem to be able to find where these hidden clips are located. My controller is still in warranty so I don't want to break them in case I can't fix my issue.

but also easy to remove using the plastic spudger along the seam, bending the bottom cover outwards

I tried this but it seems that the you need a lot of force and I ended up bending the tip of my spudger. Are you sure it's not the top cover that you need to pry away? The bottom cover has a ridge to make sure it's under the top cover so it's not easy to bend outwards.

@samomio I think there needs to be a step added for these new clips.

robplease -

Ok, not seeing a lot of motion on this request, so I've uploaded photos of the hooks to imgur.

Here ya go: https://imgur.io/a/7NWmQi5

Sean Murphy -

Life save Sean. Appreciate the image.

Vili -

This guide really needs an update on this. I had a really hard time getting the forward clips to release even after referring to the comments above. Pretty sure I broke them in the end. No big deal but would be great if the iFixit experts could work out a good method for releasing them.

Marcus Harvey -

I finally figure it out!!

The hidden clip is very tricky but once you understand how it works it is easy to remove.

Use Sean's picture: https://imgur.io/a/7NWmQi5

What sean is showing, is actually the bottom shell of the seam.

To disassemble

1. Use the flat side of the spudger, pry the bottom seam OUTWARDS near the R1/L1 button hole.

2. (most important) While prying the bottom shell seam outwards, push your thumb on the upper shell and push outward as well (you can do this by applying pressure from the removed R1/L1 button hole towards the seam. And then it will disassemble automatically

And that's it!

Penn - 27/01/24

updated instruction:

I finally figure it out!!

The hidden clip is very tricky but once you understand how it works it is easy to remove.

Use Sean's picture: https://imgur.io/a/7NWmQi5

What sean is showing, is actually the bottom shell of the seam.

To disassemble

1. Use the flat side of the spudger, pry the bottom seam OUTWARDS near the R1/L1 button hole.

2. (most important) While prying the bottom shell seam outwards, hold your thumb on the upper shell as anchor and then use your other finger to pry the bottom edge of the controller up away from the shell. If you are doing the first step, then don't worry about breaking the clip, just force it open. And then it will disassemble automatically

And that's it!

Penn -

Yes! Thanks a bunch Penn. That did the trick! Much appreciated

Sean -

I managed to do it just by pulling harder than what I was already doing. And I don't think I broke anything. So, for me at least, the technique described in this guide worked.

Riedweg Guillaume -

The video linked below clearly shows how to open the controllers with the extra clips near the L1/R1 areas.

See a video here by How To X on YouTube... https://youtu.be/djIvRoclr_E?si=dKFpQCZe...

Jason Z - 18/05/24

I really struggled with releasing the rest of the back panel (close to the shoulder buttons.) What finally seemed to do the trick for me, was doing both sides at once with upward turning motion of the back panel with the shoulder buttons approximately at the axis. Trying to release just one side and then the other felt impossible without potentially breaking the case.

dborba -

This was what did it for me

Matthew Williamson -

这里没有写

注意拆后盖的时候的用力方向

l1 和 r1 附近有卡扣，用力方向不对会破坏这两个卡扣，我的已经破掉了。

e而且这个卡扣附近有螺丝锁定，我怀疑是不是故意被设计来检测手柄有没有被拆开过。

Mussa Ding - 16/01/26

Schritt 15

Trenne das Akkukabel mit einer Pinzette oder deinen Fingern vom Motherboard.
Ziehe beim Abtrennen nicht an den Kabeln, sondern an den Steckern.

Tweezers aren't gonna grip that the way you need.

Leif DeWolf -

For those having trouble using tweezers to pull out the connector, you can grab below the lip of the connector and use the controller as a lever to pull it up as seen here DualSense Kontroller v2 Akku tauschen

This little trick helped me so much and I believe it should be shown on this guide as well.

Ezra Worthington -

Tweezers is too weak for this. I use my finger nails after removing the battery from the slot, straighten the cable lines and slowly wiggle it out.

Penn -

you’re the absolute goat

zane061 -

Tipp: I use isopropyl alcohol if a plug will not disconect. Just a few drops into the plug and it will get lose.

Nikolas Weiler -

Schritt 16

Hebe den Akku gerade aus der Halterung.

Wäre schön ein Link mit dem Werkzeug, das man braucht - Danke!

Sam Hawkins -

ALWAYS double check the polarity of the plug on your replacement battery! Compare it to your old battery. Errors can happen, particularly with 3rd party replacement batteries.

HelloMiakoda -

Schritt 17

Ziehe das Kabel des unteren Mikrofons mit einer Pinzette oder deinen Fingern aus dem Anschluss auf dem Motherboard.

These ribbon cables have small tabs on either side you can use to help pull out the cable. You can slightly pull up, alternating between the two sides, to slowly wiggle the connector out.

Tran Anh Nguyen -

Might be a rookie mistake, but DO NOT REMOVE THE WHITE BRACKETS, only the ribbon! If you do, you’ll have an awful time putting it back and will most likely mess it up. Yes I did.

Joris D -

I tried to use metal tweezers to pull this out and absolutely shredded the ribbon in the process. It's just a microphone so I wouldn't expect it to matter but now none of the games get any input from the controller even though the controller works fine in the home menu 🥲

Probably just use your fingers if you have the dexterity for it.

Grey -

As others have said, try to only remove the ribbon and not the white connector. I'd advise holding down the white connector with something (perhaps your prying tool or finger) as you pull the ribbon out gently with the tweezers.

Best to avoid pulling out the white connector if possible - but its not the end of the world if you do accidentally pull it out, as I did. You can put the connector back in but you need to be very precise with the alignment over the 6 pins it connects to on the circuit board. I had to use a magnifying glass and it took me a few attempts.

Fruke -

I didn't read the comments until it was too late and I've ended broken all the pins trying to put it back. There should be some disclaimer in here because I've just lost the mic input trying to fix a joystick and there's no getting that back. And in the most stupid way.

Jordi -

I accidentally removed the white bracket but all the pins looked straight so i just put the bracket back on

Elias -

Same thing happened to me. Please add a warning to NOT remove the white connector. I lost two of the pin sets and I’m accepting the fact I’ll never be using the mic again on this controller.

Dale Harris -

Leave the microphone attached to the battery tray, detach the ribbon cable, and lift it out as one unit.

Robert Anthony -

Schritt 18

Entferne die 6,4 mm Kreuzschlitzschraube, die die Halterung für den Akku fixiert.

Schritt 19

Hebe die Akkuhalterung vom Motherboard.

Black and red wires fit neatly under the lower left and lower right arms of the battery bracket, to avoid potential damage when reconnecting the rear case.

Seomhnasaigh B -

This needs to be noted. Thanks!

Nick Gatti -

Good call on this one for sure. You DO NOT want to crush those cables with the battery bracket.

Jack Albertelli -

Schritt 20

Löse das Kabel der rechten Tasteneinheit, indem du es mit einer Pinzette oder deinen Fingern aus dem Anschluss auf dem Motherboard ziehst.
Entferne das Flachbandkabel noch nicht ganz.

If your cables are blue and in a different position, don't sweat. It's all good. Just do the same as they do and if you feel it is necessary, label with a sharpie left and right on each cable. A simple L and R works for this case

Qbert 2030 -

My controller looks different than in the photo the connector tips are blue are the repair procedures same even if my controller is different. Please help this is my first time repairing electronics

Elias -

I noticed the different connectors i have repaired bdm 010, bdm 020 and bdm 040 controllers all the models seem to be different to identify your controller’s bdm use a website called https://exr.gg and plug in your controller with an usb cable

Elias -

Schritt 21

Greife die Lasche des Kabels an der rechten Tasteneinheit mit einer Pinzette oder deinen Fingern und trenne es von der Tasteneinheit.
Entferne das Kabel.

Depending on the revision of your controller, these ribbon cables may be slim and white and if you remove it completely, you might have to remove and tear down the trigger assembly to get the ribbon cable back in.

Robert Borrero -

maybe I'm missing something but in this case it doesn't seem to me like these cables need to be outright removed.

TheHooligan95 -

Agreed… there is no need to remove from the trigger itself. Just the motherboard. This needs to be fixed.

Jack Albertelli -

Schritt 22

Löse das Kabel der linken Tasteneinheit, indem du es mit einer Pinzette oder deinen Fingern aus dem Anschluss auf dem Motherboard ziehst.
Entferne das Flachbandkabel noch nicht ganz.

Schritt 23

Greife die Lasche des Kabels an der linken Tasteneinheit mit einer Pinzette oder deinen Fingern und trenne es von der Tasteneinheit.
Entferne das Kabel.

Be careful, the cable is extremely fragile and i wouldn’t use sharp tweezers to unplug it. I learned that the hard way.

Egor Shmoylov -

Me too, is that ribbon cable for sale separately by chance? Lol

Brn2bndair -

Schritt 24

Ziehe das Kabel des oberen Mikrofons mit einer Pinzette oder deinen Fingern aus dem Anschluss auf dem Motherboard.

what is the white thing soldered to the motherboard called where the mic ribbon cable plugs and where can i find the part?

Abhi K - 03/01/23

@abhik13943 did you ever find this part?

DaMej2895 -

unfortunately, no. i'm just using my controller without a mic.

Abhi K -

Schritt 25

Ziehe das Kabel des Touchpads mit einer Pinzette oder deinen Fingern aus dem Anschluss auf dem Motherboard.

This ribbon cable can be removed more easily by gently lifting the board to create a small gap, then using that space to pull the cable from the bottom.

Robert Anthony -

Schritt 26

Führe die Joysticks vorsichtig durch die Gehäusevorderseite und hebe das Motherboard heraus.
Die Platine wird von zwei Clips nach unten gehalten, einer zwischen ihr selbst und der rechten Triggereinheit und einer zwischen der Platine selbst und der linken Triggereinheit. Drücke behutsam auf die beiden Clips, um die Platine zu lösen.
Entferne das Motherboard noch nicht vollständig. Vier angelötete Kabel verbinden das Motherboard mit den Vibrationsmotoren.

Pushing on the joysticks makes this much easier.

zidek22 -

My motherboard wouldn't just lift right out. So I noticed there's also a pair of barely visible small black clips, one on each side of the motherboard, holding it down. One is right beside the battery connector and the other's directly across on the opposite side of the motherboard right beside the ribbon cable connector.

Jason Mulholland -

Such a good observation!

zidek22 -

That helped a lot. If you can push those tabs it comes out a lot easier. I used my tweezers to push the left one and then as others had said pushing on the joysticks from the front of the controller makes it much easier.

Fruke -

Just push on the sticks. Pops out like a charm, zero effort.

Italian Retro Guy -

Try to leave the controller on its front when you pop out the board, otherwise the speaker can fall out like mine did.

James Hartman -

Motherboard entfernen

Einleitung

Werkzeuge

Schritt 1

Schritt 2

Schritt 3

Schritt 4

Schritt 5

Schritt 6

Schritt 7

Schritt 8

Schritt 9

Schritt 10

Schritt 11

Schritt 12

Schritt 13

Schritt 14

Schritt 15

Schritt 16

Schritt 17

Schritt 18

Schritt 19

Schritt 20

Schritt 21

Schritt 22

Schritt 23

Schritt 24

Schritt 25

Schritt 26

Tinte & Feder

Sam Omiotek

0 Kommentare