Nintendo 2DS Auslösetaste austauschen

Geschrieben von: Fina Beauchamp

Kommentare: 22

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

20 - 30 Minuten

Einleitung

Hier wird der Ausbau der Auslösetaste gezeigt, entweder um sie zu reparieren oder zu reinigen.

Werkzeuge

Kreuzschlitz PH00 Schraubendreher

Schritt 1

Drehe die beiden unverlierbaren Kreuzschlitzschrauben am oberen Rückdeckel heraus.
Diese unverlierbaren Schrauben bleiben im Deckel hängen.

For context for anyone else looking at this; they sit just under the lip of the screw-hole when fully unscrewed for the purposes of lifting the panel - sometimes flush with the plate. The screw hasn't threaded if you try taking it further up - its just that the screw never goes "above" the edge of the hole - the little click and reset it does is the washer inside keeping it in place doing its job.

DIY Person -

Schritt 2

Drehe den Deckel nach oben und nach außen um ihn zu entfernen.

My apologies for the poor image quality in comparison to the rest. If someone can replace it with a higher quality image in the future it'd be much appreciated.

DIY Person -

Schritt 3

Entferne den Akku aus seinem Fach. Hebe ihn dazu an der Seite die direkt an der Außenkante liegt hoch.

Schritt 4

Entferne die zehn Kreuzschlitzschrauben, mit denen die Rückabdeckung befestigt ist.

Can't take off the screw top left next to the battery. What type of screwdriver do I use and where can I find some?

Little Mac - 19/02/18

I used a husky with changeable heads, you could probably find one on amazon

Minecrafter Pig - 22/04/19

These screws aren't Phillips, they're JIS, if you use a Phillips head you can and will strip the screws, please update this as it can cause more harm to people's systems than good if they get stripped.

Sneakii -

yep. i stripped my screws

Persvicx -

The screws are 6.2mm long

Martin Samuelsson -

god I thought it was because I was repairing a sibling's ds that had something spilled on it (idk maybe that they didn't clean it good when it happened) but continued to struggle even with screws that looked fine... wish I had checked the comments sooner :/ Please like the above, update this guide! It sucks knowing that someone like me is also gonna probably miss this. I didn't get super far but well. I already stripped down some which sucks either way. Ironically, I noticed that using a size slightly smaller gets the job done better. Ironic in that you'd normally avoid that because it's more likely to strip with small bits scrapping the inside. But if you are real careful it can hang on and twist. I'd recommend just getting the JIS but maybe this might work for some- I also want to emphasize SLIGHTLY smaller phillips.

Alexandria.P -

Schritt 5

Die Rückabdeckung ist mit einem Flachbandkabel an der Hauptplatine verbunden. Entferne sie deswegen nicht zu weit vom Gerät.
Ziehe die Rückabdeckung vorsichtig vom Gerät weg nach oben.

Y si se corta el cable que pasa?

Laura Pernía López -

Schritt 6

Klappe den Sicherungsbügel des Flachbandkabels mit dem Fingernagel oder dem flachen Ende des Spudgers hoch und ziehe das Kabel von der Hauptplatine ab.
Löse das Kabel aus dem Anschluss ab.
Nutze die Gelegenheit um gleich die rechte und linke Auslösetaste zu entfernen. Sie haben eine Feder und eine Achse, achte darauf diese Teile nicht zu beschädigen oder zu verlieren.

You can also detach the cable from the motherboard safely by flipping up the connector on the motherboard. Just don't forget to reattach. Some will find this tedious but may save time if you know what you're doing with said connectors.

Blackbeard - 03/07/16

I agree, this is what the guide i followed said to do and since I was disconnecting all the other ribbon cables it made perfect sense to do it that way.

Lin -

pay attention: my 2ds dropped it's lens covers at this step

Jos van Reenen - 13/03/17

Likewise, I used a tiny drop of glue to put the lens back in place. Take care not to dirty the lens.

Elliot West - 01/12/19

The picture you have there has the camera lens ribbon installed upside down. The ribbon needs to be pointing down when you re-attach it not up.

Rick Parrish - 04/05/17

Agreed, ribbon cable looks upside down in picture

Elliot West - 01/12/19

Schritt 7

An der Auslösetaste sind kleine Federn befestigt, sei deswegen vorsichtig, wenn du sie vom Gerät entfernst.
Ziehe die Auslösetaste weg vom Gerät und entferne sie.

Thanks so much for these instructions. My nine year-old son just got Pokemon Sun and Moon on Friday evening. He had been talking about it non-stop for several months. On Saturday, he managed to bend the plastic lip on the base of his 2DS right trigger - the trigger button no longer worked. He was devastated, because we thought he had permanently broken his 2DS. We were afraid he would have to wait until Christmas (over a month away) before we could get him a new one.

I found these instructions via Google, followed them to take apart his 2DS and remove the trigger button. I gently bent the plastic lip of the trigger back with needle nose pliers, reassembled the 2Ds, and the trigger worked perfectly! He now thinks I am the greatest dad in the world.

bruce - 20/11/16

same situation here

Minecrafter Pig - 23/04/19

Hi there, does anyone know which type of springs they use in a 2DS? Because I don't really want to pay 7€+15€ shipping just to replace one spring I lost and I could get most sorts and sizes of springs in a hardware store for less than 5€ for 50.

Any help would be very appreciated.

Christian Adamczyk -

i did a teardown of my 2ds, and for some reason the L button was disconnected from the motherboard. i don't mean the plastic piece, i mean the little black button came unsoldered from the motherboard?

skibiid sigma -