Disassembly Guides

Wacom Cintiq Pro 13 Disassembly

Wacom Cintiq Pro 13 Disassembly

Tools

These are some common tools used to work on this device. You might not need every tool for every procedure.

Technical Specs and Compatible Accessories

Display:

  • 13” Full HD (1920x1080) IPS matte screen with wide color gamut, 87% of Adobe RGB

Ports:

  • 3x USB type C port
  • 1x Audio 3,5mm jack
  • 1x USB 3.0 Card Reader

Compatible Pens:

  • Wacom Pro Pen 2
  • Wacom Pro Pen Slim
  • Wacom Pro Pen 3D

Compatible Power Adapters:

  • Wacom 100W USB-C Power Adapter ADP-100PB
  • Wacom 45W USB-C Power Adapter ACK4281401
  • Any other USB-C Power adapter with 20V output (at least 45W) (Commonly sold as Laptop Power Adapters)

Connection types and compatible adapters:

USB-C to USB-C connection

  • In order to use it with USB-C to USB-C connection, host device (PC/Mac) must support USB-C DisplayPort Alternate Mode

Displayport/HDMI to USB-C

By using

  • Wacom Link (Mini Displayport)
  • Wacom Link Plus (Mini Displayport [up to 4K] and HDMI [up to QHD] )

Warning - most USB-C adapters allow only USB-C host (PC/Mac) to DisplayPort/HDMI monitor connection, not in reverse as required by Cintiq 13/16 and other USB-C monitors

Extra information

  • Can be used as drawing tablet with touch functionality by connecting USB 2.0 to USB-C cable and power adapter directly to any tablet USB-C port, and not connecting any display inputs

Components and Servicing

Extra servicing information

  • “Power button and touch display controls” board is placed under front glass, requiring front glass removal or cutting plastic casing inside the tablet to remove and replace it
  • Casing is glued using very strong adhesive, making it very hard to open the device without any damage
  • Audio jack board is separated from the mainboard, making it soldering-free replacement part.
  • Most firmware is stored in 25 SPI Flash EEPROM chips, and can be reprogrammed using cheap BIOS programmers, eg. CH341A
  • Pen firmware is stored in Wacom Pen Controller chip, and there is no easy method to fix it if it has failed.
  • Display used in this device is a 13” inch laptop-like display and uses 30-pin edisplayport connector
  • LCD Display used in this tablet is a custom part, with pen digitizer as one of it's layers, just under backlight layers. Replacement will require same model of LCD Panel to be used.
  • LCD Display is glued to the touch digitizer layer, which then, is glued, to the front glass.

Mainboard components

  • Realtek RTD2786B LCD scaler (handles both display and audio) (+ SPI Flash EEPROM firmware chip)
  • 128MB DDR3 memory
  • Kinetic STDP4028 LVDS to DisplayPort transmitter (+ SPI Flash EEPROM firmware chip)
  • Three USB-C TI TPS65982 controllers (+ 3x SPI Flash EEPROM firmware chips)
  • Genesys GL3224 USB 3.0 Card Reader controller (+ SPI Flash EEPROM firmware chip)
  • Two USB 3.0 Hubs
  • Wacom Pen Controller chip
  • FTDI FT232 USB to UART controller

Internal components

  • Mainboard 4H.3GCA8.A00
  • Wacom Pen digitizer boards (PWB-C800-C + PWB-C929-C)
  • Audio jack board
  • Power button board with touch controls
  • BOE NV133FHM-A52 Display (May vary from unit to unit)