Disassembling Macintosh IIsi Power Supply

Written By: Chris Green
  • Comments: 4
Disassembling Macintosh IIsi Power Supply

Difficulty

Moderate

Steps

8

Time Required

15 - 30 minutes

Introduction

The Macintosh IIsi Uses a 120/240V AC Power Supply. It provides power directly to the logic board. From there, it is distributed to the rest of the computer.

  1. r1Cft2VV1RGPfyL4
    r1Cft2VV1RGPfyL4
    KKeUmPgMYaLdaiGt

    • Start by turning the computer around, and remove this #0 Phillips Screw.

    • There may or may not be a Phillips #0 screw here, depending on whether or not the computer has ever been serviced.

  2. DkSfMxh4aHLiqFXJ
    DkSfMxh4aHLiqFXJ
    PkSg1D2OL5ANuCOP
    NRNA5eL3FkOPxxln

    • Now lift these two clips, and slowly pivot the case up.

    • You can now seperate the top of the computer from the rest of the machine.

  3. 6uWIE3nlkW2pCRfT
    6uWIE3nlkW2pCRfT
    kcqnxDXHExR4xu6e
    42LAcjGpQwAgv2Kx

    • The "SuperDrive" is mounted similarly to the hard drive, and positioned right next to it.

    • Push these two tabs out, and lift the drive up.

  4. hI4SlHgaOJpKXSfF
    hI4SlHgaOJpKXSfF
    OxgRi1TlIlDGtURK
    32OFT3DnmAXKYxll

    • Flip the drive so it is on top of the power supply, and remove the "Red-Ribbon" cable.

    • 1.44MB floppy drives need a ribbon cable with a red stripe on one side. 400KB floppy drives use a ribbon cable with a yellow stripe on one side. 800KB floppy drives can use a red, or yellow striped cable.

    • This drive was manufactured by Sony in 1990.

  5. 1UCQiPuD3stfXhHU

    • The fan recieves power from two contacts on the logic board and has no connector.

  6. wfYE1QMgfyMYx6Jh
    wfYE1QMgfyMYx6Jh
    WIUDHAmCbehQYa2j
    UsB4jrGapO2fK3yp

    • In all of the years that I have worked on this machine, I have found no good way to remove the fan.

    • The best way to start, is to push in here on the side of the fan.

    • Being careful not to exert too much force, try to push in, and wiggle the fan outward as such. (2nd Photo)

    • You can now lift the fan all the way out, and remove it.

    • The Fan Power Contacts on the Logic Board:

    There is no need to pull out the fan. Just take a knife and you can squeeze the tab in step 7

    Willy Kaiser -

    I wanted to second what Willy said; as far as I can tell one is intended to remove the PSU before the fan. You just jam something the right width in between so the PSU tab is depressed, pull it out, and after the PSU is out removing the fan is easy.

    Caleb Hansberry -

  7. dkZhRsuOQgULtYQo
    dkZhRsuOQgULtYQo
    4bW5ZEVfXUAunN1x

    • To remove the power supply, squeeze these two tabs and lift the front up.

    • On the back of the power supply, there is a tab that also must be pressed to remove the power supply fully. You can then lift it out all the way. A firm tug may be necessary to seperate the power connector.

  8. AEoAjoxZcfPhP4Hi
    AEoAjoxZcfPhP4Hi
    c65dbxBGsJkQ2GVk

    • Information on the power supply:

    • It was made by Sony in 1990, and uses a 10-Pin power connector.

    The power supply on mine is corroded. Cannot even do a re-cap. Any suggestions for an alternate power supply or where to buy a reasonably cost-effective replacement?

    Charles -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Chris Green

Member since: 11/10/09

35572 Reputation

One comment

I was looking for the schematic for the power supply APS-06 pictured here. The information above would be a little helpful if one was really unaware of anything electromechanical,… otherwise, it’s all pretty obvious I think.

nikitesla -