Motorola Moto E4 Plus Battery Replacement

Written By: Dominik Schnabelrauch
  • Comments: 3
Motorola Moto E4 Plus Battery Replacement

Difficulty

Moderate

Steps

12

Time Required

20 - 50 minutes

Introduction

Use this guide to remove and replace the battery in the Motorola Moto E4 Plus (XT1771).

Before disassembling your phone, discharge the battery below 25%. If your battery is swollen, do not heat your phone. Swollen batteries can be very dangerous, so wear eye protection and exercise due caution, or take it to a professional if you're not sure how to proceed.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. PCCXuPCwmVpwtTCZ
    PCCXuPCwmVpwtTCZ
    bPy2yicrAdZxADOP
    2lalNWm6HLMBs6AH

    • Power off your phone before beginning disassembly.

    • Insert the edge of the spudger into the notch on the bottom right corner of the phone.

    • Twist the spudger to start releasing the back cover from the phone.

    • Slide the spudger along the bottom edge to separate the back cover from the phone.

  2. BUAOpKayenHBerHv
    BUAOpKayenHBerHv
    Hajy1vGJYVD5BJSq

    • Lift the phone unit out of the back cover.

  3. uQUf2htv3tBFguXy

    • Remove the eighteen 3.3 mm Phillips screws securing the midframe assembly.

  4. OB1nkHUu13UkPsEx
    OB1nkHUu13UkPsEx
    rBkIaTHeKhMtjbnV

    • Remove the charging board cover.

  5. qvAwQyXWkDpEM63D
    qvAwQyXWkDpEM63D
    oUeTRnhFSk3kbbsG
    pAjwAZVrCdQmOVNV

    • Remove the battery cover.

    Hoe kom ik aan een nieuwe cover of waar is die te koop.

    Antoinet -

  6. SG3BidfIJhuNVmRI
    SG3BidfIJhuNVmRI
    LW6CdknPWSEdboFQ

    • Insert an opening pick underneath the bottom left corner of the motherboard cover.

    • Slide the opening pick between the cover and the second SIM tray to release the plastic clip.

  7. dLcpNWeDPW1VGJRG
    dLcpNWeDPW1VGJRG
    UDi3hWIsviVro5EK

    • Insert an opening pick underneath the bottom right corner of the motherboard cover.

    • Use the opening pick to pry up the motherboard cover.

  8. Sc63bxRyFcvihlew
    Sc63bxRyFcvihlew
    HfOHa1LZakKp1sxy

    • Remove the motherboard cover.

  9. HBto2G6tNJGtUVDf
    HBto2G6tNJGtUVDf
    ZoFWKvCn4ZLJMlmU

    • Use the edge of a spudger to pry up and disconnect the battery flex cable from the motherboard.

  10. CEbxdAdFBFaFGyaI
    CEbxdAdFBFaFGyaI
    Una1lycUhWCAZTq5
    ZKfI6LWvxE5LqwNR

    • Use a pair of tweezers to peel the ends of the two pull tabs off of the bottom edge of the battery.

  11. AspDXjnXaXCrKjuD
    AspDXjnXaXCrKjuD
    oidmy3pNQVEju3l3
    MGA3aJVlAHPqxHVD

    • Pull out the left adhesive strip by steadily pulling the left tab at a flat angle.

    • If the adhesive strip rips, grab and twist the remaining stub around the tip of a pair of tweezers a couple of times and then continue pulling.

    • Repeat the same process for the right adhesive strip.

  12. ZSurQJM1WTqRXOfL
    ZSurQJM1WTqRXOfL
    HhZrmH51HyL2UuOE

    • Remove the battery.

    • Do not reuse the battery after it has been removed, as doing so is a potential safety hazard. Replace it with a new battery.

    • Secure the new battery with pre-cut adhesive or double-sided adhesive tape.

    • In order to position it correctly, apply the new adhesive into the phone at the places where the old adhesive was located, not directly onto the battery.

    • Press the new battery firmly into place for 5-10 seconds.

    Parfait, très clair, 1/4 d’heure pour le remplacement, un peu de bagarre avec les auto collants mais tout s’est bien passé, la batterie est pleine à 86%, faut-il quand même la charger ?

    Dantrente -

    Bonjour,

    Pour obtenir des performances optimales, après avoir terminé ce guide, calibrez votre batterie nouvellement installée: chargez-la à 100% et continuez à la recharger pendant au moins deux heures. Ensuite, utilisez votre appareil jusqu'à ce qu'il s'éteigne en raison d'une batterie faible. Enfin, chargez-le sans interruption à 100%.

    Arthur Shi -

Conclusion

To reassemble your device, follow these instructions in reverse order.

If possible, turn on your phone and test your repair before installing new adhesive and resealing the phone.

For optimal performance, after completing this guide, calibrate your newly installed battery: Charge it to 100% and keep charging it for at least two more hours. Then use your device until it shuts off due to low battery. Finally, charge it uninterrupted to 100%.

Author

Dominik Schnabelrauch

Member since: 23/11/16

167336 Reputation

0 comments