Battery Disconnection

Geschrieben von: Adriana Zwink
  • Kommentare: 1
Battery Disconnection

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

35 - 50 Minuten

Einleitung

This is a prerequisite guide! This guide is part of another procedure and is not meant to be used alone.

Use this guide to disconnect the battery in the Xiaomi Poco F3.

  1. jmXNfxGvVYm1OJZ3

    • Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the screen and internal battery are both susceptible to heat damage.

  2. xMGNQXeidNTbWlwD
    xMGNQXeidNTbWlwD
    MEewbfsMyB1NCrkd

    • Secure a suction handle to the right edge of the rear glass, as close to the edge as possible.

    • If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the rear glass with the suction handle to create a small gap between the rear glass and the frame.

    • In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Insert an opening pick into the gap you created.

  3. YEkjkS6yPJUJZRvG
    YEkjkS6yPJUJZRvG
    QPQ3KSoOtLjwo4wF

    • Slide the opening pick to the top right corner to slice the adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  4. clBHRbyRZOZ6FeGf
    clBHRbyRZOZ6FeGf
    G2DcwGJEwytQYLfN
    Ug2RTKADrfRgOQhM

    • Insert a second opening pick at the top right corner.

    • Slide the opening pick to the bottom right corner to slice the adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  5. cFk4poZAHGXx6AyG
    cFk4poZAHGXx6AyG
    BM1qwQZPATUVZKRh

    • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener for one to two minutes to reheat it.

    • Insert a third opening pick in the bottom right corner.

    • Slide the opening pick along the bottom edge of your phone to slice the adhesive.

    • Leave the opening pick in the bottom left corner to prevent the adhesive from resealing.

  6. EYsDnJy4jfgy3eZc
    EYsDnJy4jfgy3eZc
    uumDXVMRABDopeIp
    BNukG3AEt3tSytJY

    • Insert a fourth opening pick in the bottom left corner of your phone.

    • Slide the opening pick along the left edge to slice the adhesive.

    • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

  7. JqAPFDpZ1P1KCF6N
    JqAPFDpZ1P1KCF6N
    2VIbvM3x6bxc6sij

    • Insert a fifth opening pick underneath the top left corner.

    • Slide the opening pick along the top edge of the rear glass to slice the remaining adhesive.

  8. HUIMlPiajTLHiLnW

    • Remove the rear glass.

    • Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

    • Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

    Can someone please tell me what the little circular grill next to the cameras is? Ive made tests for all the sensors and I don't think it's a speaker grill.

    Nikola Jovancevski -

  9. jUiOn3qaUjXJYoKO

    • Use a Phillips screwdriver to remove the eleven screws securing the motherboard cover:

    • Ten 3.4 mm-long screws

    • One 1.5 mm-long screw

  10. cRftTJ6YYEMkSlKC
    cRftTJ6YYEMkSlKC
    sN1DXJCogIteLdkE

    • Insert the tip of an opening pick under the bottom left edge of the motherboard cover.

    • Use the opening pick to lift up the motherboard cover and release the plastic clips that hold the cover in its place.

    • Don't remove the motherboard cover all the way yet! It's still connected to the motherboard.

  11. vANmPWwKW1ywoWHs
    vANmPWwKW1ywoWHs
    OWLRC6XsQkSQ61N2

    • Use your fingers to lift up the motherboard cover to access the connector on the motherboard.

    • Use a spudger to disconnect the motherboard cover by prying the connector straight up from its socket at the motherboard.

    • Remove the motherboard cover.

  12. lNenWKmEnGsW2AGv
    lNenWKmEnGsW2AGv
    iIuNwPftY4CAsEh1

    • The battery connector is covered by a graphite foil. Carefully fold it up or tape it to the top edge of the Poco F3 to access the battery connector.

    • Use a spudger to disconnect the battery by prying the connector straight up from its socket.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Adriana Zwink

Mitglied seit: 18/12/19

38806 Reputation

0 Kommentare