Echo Chain Saw CS590 2019 Front Hand Guard Replacement

Geschrieben von: Alex Diaz-Kokaisl
  • Kommentare: 0
Echo Chain Saw CS590 2019 Front Hand Guard Replacement

Schwierigkeitsgrad

Moderate

Schritte

12

Zeitaufwand

20 - 40 Minuten

Einleitung

Use this guide to replace the front hand guard in your Echo Chain Saw CS-590 (2019).

  1. EXqrpoIiVuTlWQpj
    EXqrpoIiVuTlWQpj
    HdgxWTa3PoaumQwV

    • Make sure you have the ignition switch turned off before starting your repair.

    • The chainsaw should be cool to the touch before continuing.

  2. VlDpTlKOKZAQGHeb
    VlDpTlKOKZAQGHeb
    lHMfIELUULyDD2XT

    • Use your fingers to loosen the air filter cover knob.

  3. hM5CJiHDnD4G2taS
    hM5CJiHDnD4G2taS
    pOHJ11GAZ5EvoCvZ
    YMmTvYbwPcaXOWxb

    • Remove the air filter cover.

  4. MjMcC4LWGGjshQhJ
    MjMcC4LWGGjshQhJ
    XcEo1FphwtCChEHW
    pqvhItih2LOKvZkk

    • Use your fingers to pull up and disconnect the spark plug boot.

  5. uIeULaEtZwacg5vq
    uIeULaEtZwacg5vq
    OnvVeeJSK6X1Ku5A
    HRTNwxHDJfPRhkwd

    • To minimize debris entering the intake, pull the choke shut before continuing.

    • Remove the air filter

    • During reassembly, clean the air filter with compressed air or with light brushing before reinstalling it.

  6. fprWV6JLP2CWaXvu
    fprWV6JLP2CWaXvu
    fnYwu2PlJm1UPPPU

    • Use a T25 Torx screwdriver to remove the five screws securing the front handle to the bottom and right side of the device:

    • Four 24 mm-long screws

    • One 25 mm-long screw

  7. GFJMPFFC6UrZtvFN
    GFJMPFFC6UrZtvFN
    STkUQDHYn5oWvtJd
    ksfCfYQdLRNxy3oB

    • Pull the handle toward the rear of the device to remove it.

  8. ZRPLAVeHjFMaSONl
    ZRPLAVeHjFMaSONl
    qlhmPLC2WBLXOhXk

    • Use a 13 mm wrench to remove the two nuts securing the sprocket guard.

  9. SlcKdx1dtwlotJtM
    SlcKdx1dtwlotJtM
    rivpeHXNpLLJYHpF
    temJNuTUTyqpyGlG

    • Remove the sprocket guard.

  10. C4EWcYOQwvLJitjw
    C4EWcYOQwvLJitjw
    MNXVHVVXHUounYit
    LUZrk2qmpW1FHLGE

    • Push the guide bar towards the back of the device to create slack in the saw chain.

    • Pull the guide bar away from the device to separate the saw chain from the clutch drum.

    • Remove the guide bar.

  11. JFMCcfuYLvUA624B
    JFMCcfuYLvUA624B
    sCEQTtNqlMHSDivY

    • Make sure the front hand guard is in the unlocked position before continuing.

    • Use a T25 Torx screwdriver to remove the two 20 mm screws securing the front hand guard.

  12. yqeipxYZgcrRlLKe
    yqeipxYZgcrRlLKe
    p63V56LxB4weIiRI

    • Pull the front hand guard toward the rear of the device to remove it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alex Diaz-Kokaisl

Mitglied seit: 16/01/22

69204 Reputation

0 Kommentare