Echo Chain Saw CS590 2019 Guide Bar Replacement

Geschrieben von: Alex Diaz-Kokaisl
  • Kommentare: 0
Echo Chain Saw CS590 2019 Guide Bar Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

20 - 40 Minuten

Einleitung

This is a prerequisite-only guide! This guide is part of another procedure and is not meant to be used alone.

Use this guide to replace the guide bar in your Echo Chain Saw CS-590 (2019).

  1. EXqrpoIiVuTlWQpj
    EXqrpoIiVuTlWQpj
    HdgxWTa3PoaumQwV

    • Make sure you have the ignition switch turned off before starting your repair.

    • The chainsaw should be cool to the touch before continuing.

  2. VlDpTlKOKZAQGHeb
    VlDpTlKOKZAQGHeb
    lHMfIELUULyDD2XT

    • Use your fingers to loosen the air filter cover knob.

  3. hM5CJiHDnD4G2taS
    hM5CJiHDnD4G2taS
    pOHJ11GAZ5EvoCvZ
    YMmTvYbwPcaXOWxb

    • Remove the air filter cover.

  4. MjMcC4LWGGjshQhJ
    MjMcC4LWGGjshQhJ
    XcEo1FphwtCChEHW
    pqvhItih2LOKvZkk

    • Use your fingers to pull up and disconnect the spark plug boot.

  5. uIeULaEtZwacg5vq
    uIeULaEtZwacg5vq
    OnvVeeJSK6X1Ku5A
    HRTNwxHDJfPRhkwd

    • To minimize debris entering the intake, pull the choke shut before continuing.

    • Remove the air filter

    • During reassembly, clean the air filter with compressed air or with light brushing before reinstalling it.

  6. fprWV6JLP2CWaXvu
    fprWV6JLP2CWaXvu
    fnYwu2PlJm1UPPPU

    • Use a T25 Torx screwdriver to remove the five screws securing the front handle to the bottom and right side of the device:

    • Four 24 mm-long screws

    • One 25 mm-long screw

  7. GFJMPFFC6UrZtvFN
    GFJMPFFC6UrZtvFN
    STkUQDHYn5oWvtJd
    ksfCfYQdLRNxy3oB

    • Pull the handle toward the rear of the device to remove it.

  8. ZRPLAVeHjFMaSONl
    ZRPLAVeHjFMaSONl
    qlhmPLC2WBLXOhXk

    • Use a 13 mm wrench to remove the two nuts securing the sprocket guard.

  9. SlcKdx1dtwlotJtM
    SlcKdx1dtwlotJtM
    rivpeHXNpLLJYHpF
    temJNuTUTyqpyGlG

    • Remove the sprocket guard.

  10. C4EWcYOQwvLJitjw
    C4EWcYOQwvLJitjw
    MNXVHVVXHUounYit
    LUZrk2qmpW1FHLGE

    • Push the guide bar towards the back of the device to create slack in the saw chain.

    • Pull the guide bar away from the device to separate the saw chain from the clutch drum.

    • Remove the guide bar.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alex Diaz-Kokaisl

Mitglied seit: 16/01/22

69204 Reputation

0 Kommentare